Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1870/66    Short in Driver Side Front Seat Cushion Squib Circuit

DTC    B1871/66    Open in Driver Side Front Seat Cushion Squib Circuit

DTC    B1872/66    Short to GND in Driver Side Front Seat Cushion Squib Circuit

DTC    B1873/66    Short to B+ in Driver Side Front Seat Cushion Squib Circuit

for Preparation Click here


DESCRIPTION

The driver side front seat cushion squib circuit consists of the airbag sensor assembly and front seat airbag sub-assembly LH.
The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the driver side front seat cushion squib circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1870/66
  1. The airbag sensor assembly receives a line short circuit signal in the driver side front seat cushion squib circuit during primary check.
  2. Driver side front seat cushion squib malfunction
  3. Airbag sensor assembly malfunction
  1. Floor wire
  2. Front seat airbag sub-assembly LH (Driver side front seat cushion squib)
  3. Airbag sensor assembly
B1871/66
  1. The airbag sensor assembly receives an open circuit signal in the driver side front seat cushion squib circuit.
  2. Driver side front seat cushion squib malfunction
  3. Airbag sensor assembly malfunction
B1872/66
  1. The airbag sensor assembly receives a short circuit to ground signal in the driver side front seat cushion squib circuit.
  2. Driver side front seat cushion squib malfunction
  3. Airbag sensor assembly malfunction
B1873/66
  1. The airbag sensor assembly receives a short circuit to B+ signal in the driver side front seat cushion squib circuit.
  2. Driver side front seat cushion squib malfunction
  3. Airbag sensor assembly malfunction

WIRING DIAGRAM


C249389E04


INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).

HINT:
  1. Perform the simulation method by selecting check mode (Signal Check) using the Techstream (Click here).
  2. After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (Click here).

1.CHECK CONNECTORS


    C241752E01
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the front seat airbag sub-assembly LH and airbag sensor assembly.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the front seat airbag sub-assembly LH and airbag sensor assembly.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.

  1. Check that the short spring for the floor wire with the activation prevention mechanism is not deformed or damaged.

    OK:
    The short spring is not deformed or damaged.

    Text in Illustration 
    *1
    Front Seat Airbag Sub-assembly LH
    *2
    Airbag Sensor Assembly
    *3
    Floor Wire



NG
REPLACE FLOOR WIRE
OK


2.CHECK FRONT SEAT AIRBAG SUB-ASSEMBLY LH (DRIVER SIDE FRONT SEAT CUSHION SQUIB)


    C249372E01
  1. Connect the connector to the airbag sensor assembly.

  1. Connect SST (resistance 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the front seat airbag sub-assembly LH (driver side front seat cushion squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting it.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1870/66, B1871/66, B1872/66 or B1873/66 is not output.

    HINT:
    Codes other than DTCs B1870/66, B1871/66, B1872/66 and B1873/66 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Disconnect SST from connector C.
    Text in Illustration 
    *1
    Front Seat Airbag Sub-assembly LH
    *2
    Airbag Sensor Assembly
    *a
    Front view of wire harness connector
    (to Front Seat Airbag Sub-assembly LH)



NG
Go to step 3
OK

REPLACE FRONT SEAT AIRBAG SUB-ASSEMBLY LH (Click here)  

3.CHECK FLOOR WIRE


    C249373E01
  1. Disconnect the floor wire from the airbag sensor assembly.

  1. Check for a short to B+ in the circuit.

    1. Connect the cable to the negative (-) auxiliary battery terminal.

    2. Turn the ignition switch to ON (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      M34-2 (FCD+) - Body ground
      Ignition switch ON (IG)
      Below 1 V
      M34-1 (FCD-) - Body ground
      Ignition switch ON (IG)
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:
      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Check for an open in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      M34-2 (FCD+) - M34-1 (FCD-)
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      M34-2 (FCD+) - Body ground
      Always
      1 MΩ or higher
      M34-1 (FCD-) - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      M34-2 (FCD+) - M34-1 (FCD-)
      Always
      1 MΩ or higher

    3. Restore the released activation prevention mechanism of connector B to the original condition.
      Text in Illustration 
      *1
      Front Seat Airbag Sub-assembly LH
      *2
      Airbag Sensor Assembly
      *3
      Floor Wire
      *a
      Front view of wire harness connector
      (to Front Seat Airbag Sub-assembly LH)



NG
REPLACE FLOOR WIRE
OK


4.CHECK DTC


    C238245E01
  1. Connect the connectors to the front seat airbag sub-assembly LH and airbag sensor assembly.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1870/66, B1871/66, B1872/66 or B1873/66 is not output.

    HINT:
    Codes other than DTCs B1870/66, B1871/66, B1872/66 and B1873/66 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Front Seat Airbag Sub-assembly LH
    *2
    Airbag Sensor Assembly



NG
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)