OIL PUMP > INSTALLATION |
| 1. INSTALL OIL PUMP SEAL |
Apply a light coat of MP grease to the timing chain cover oil pump seal lip.
![]() |
Using SST and a wooden block, tap in a new oil pump seal until its surface is flush with the timing chain cover edge.
| *1 | Wooden Block |
| 2. INSTALL TIMING CHAIN COVER |
Install 2 new O-rings to the cylinder block and oil pan.
Apply seal packing to the timing chain cover and engine assembly as shown in the illustration below.

| *a | Apply Seal Packing To The Inner Corners | *b | 2.5 mm Or Higher |
| *c | Seal Packing Application Width 3.5 to 4.5 mm | *d | Seal Packing Application Width 1.5 to 2.0 mm |
| *e | Seal Packing Application Width 10 mm or more | *f | Upper View |
| *g | Apply enough seal packing so that it will protrude beyond the timing chain cover installation surface | - | - |
![]() |
Align the oil pump drive rotor spline and the crankshaft as shown in the illustration.
| *a | Drive Rotor Spline |
| *b | Crankshaft |
Temporarily install the timing chain cover and 2 wire harness clamp brackets with the 18 bolts and nut.

| *1 | Nut | *2 | Wire Harness Clamp Bracket |
| Item | Length | Thread Diameter |
| Bolt A | 20 mm (0.787 in.) | 6 mm (0.236 in.) |
| Bolt B | 30 mm (1.18 in.) | 8 mm (0.315 in.) |
| Bolt C | 35 mm (1.38 in.) | 6 mm (0.236 in.) |
| Bolt D | 20 mm (0.787 in.) | 8 mm (0.315 in.) |
Tighten the 18 bolts and nut in the sequence shown in the illustration.
| 3. INSTALL SCREW PLUG |
Apply a few drops of adhesive to 2 or 3 threads of the screw plug.
Using an 8 mm hexagon socket wrench, install the screw plug.
| 4. INSTALL ENGINE MOUNTING BRACKET RH |
Temporarily install the engine mounting bracket RH with the 4 bolts.
![]() |
Tighten the 4 bolts in the sequence shown in the illustration.
| 5. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE |
Apply a light coat of engine oil to a new O-ring and install the O-ring to the engine oil level dipstick guide.
Install the engine oil level dipstick guide with the bolt.
| 6. INSTALL ENGINE OIL LEVEL DIPSTICK |
Install the engine oil level dipstick.
| 7. INSTALL CRANKSHAFT DAMPER SUB-ASSEMBLY |
Align the hole of the crankshaft damper sub-assembly with the straight pin, then install the crankshaft damper sub-assembly.
![]() |
Using SST, hold the crankshaft damper sub-assembly in place and tighten the bolt.
| *a | Hold |
![]() | Turn |
| 8. INSTALL CRANKSHAFT POSITION SENSOR |
![]() |
Apply a light coat of engine oil to the O-ring on the crank position sensor.
| *1 | O-ring |
Install the crank position sensor with the bolt.
| 9. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY |
Install a new gasket to the cylinder head cover sub-assembly.
![]() |
Apply seal packing to the 2 locations shown in the illustration.
![]() | Apply Seal Packing |
![]() |
Temporarily install the cylinder head cover sub-assembly with the 9 bolts, 2 nuts and 2 new seal washers.
| *1 | Seal Washer |
Using several steps, uniformly tighten the bolts and nuts in the sequence shown in the illustration.
Connect the No. 1 ventilation hose and No. 2 ventilation hose.
| 10. CONNECT ENGINE WIRE |
Install the engine wire with the 3 bolts.
Connect the wire harness clamp.
Connect the 4 injector connectors.
| 11. INSTALL IGNITION COIL ASSEMBLY |
![]() |
Install the 4 No. 1 ignition coils with the 4 bolts.
| *a | Body |
| *b | Cap |
Connect the 4 No. 1 ignition coil connectors.
| 12. INSTALL EGR VALVE WITH COOLER ASSEMBLY |
Using an E8 "TORX" socket wrench, install the 2 stud bolts.
Install a new gasket and the EGR valve assembly with the 2 bolts.
Connect the No. 1 water by-pass hose.
Temporarily install a new gasket and the EGR valve with cooler assembly with the 2 bolts and 2 nuts.
Install the EGR valve bracket with the 2 bolts and nut.
Install the EGR valve with cooler assembly with the 2 bolts and 2 nuts.
![]() |
Connect the No. 4 water by-pass hose and No. 5 water by-pass hose.
| *a | 2 to 7 mm (0.079 to 0.276 in.) |
| *b | Up |
| *c | 90° |
| *d | Engine Rear |
Install the wire harness clamp bracket with the bolt.
![]() |
Connect the 2 connectors and wire harness clamp.
| 13. INSTALL NO. 2 EGR PIPE |
![]() |
Install 2 new gaskets and the No. 2 EGR pipe with the 2 bolts and 2 nuts.
Connect the clamp and No. 2 water by-pass hose.
Connect the wire harness clamp.
| 14. REMOVE ENGINE STAND |