Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BLACK OUT TAPE (for Front Door)

BLACK OUT TAPE (for Front Door) > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for both the RH and LH side.
  2. The procedure described below is for the LH side.



1. REPAIR INSTRUCTION
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.
      Heating Temperature 
      Item
      Temperature
      Vehicle Body
      40 to 60°C (104 to 140°F)

      NOTICE:
      Do not heat the vehicle body excessively.

    2. Wipe off any tape adhesive residue with cleaner.

  1. Installation temperature

    1. When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape up to between 20 and 30°C (68 and 86°F) using a heat light. When the ambient temperature is above 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape down to between 20 and 30°C (68 and 86°F) prior to installation.

      HINT:
      1. The most appropriate temperature for installing the tape is 25°C (77°F).
      2. When the temperature is low, the tape turns stiff and comes off easily. When the temperature is high, the tape elasticity increases.

  1. Before installation

    1. Remove any coating roughness or dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame). If any roughness or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.

      HINT:
      Spray water on the shop floor to settle any dust.

  1. Key points for handling the tape

    1. The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and flat.

      NOTICE:
      Do not bend the tape or leave it in high temperature places.



  1. Key points for installation of the tape (how to use a squeegee and installation procedure for flat surfaces)

    NOTICE:
    1. Position the tape accurately to achieve a neat finish and to avoid peeling.
    2. The tape cannot be reused because it deforms and will not fit any more after being removed.




    1. To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee at 40 to 50° (pressing forward) or 30 to 45° (pulling) to the vehicle body surface and press the tape onto the vehicle body surface with a force of 20 to 30 N (2 to 3 kgf, 4.5 to 6.7 lbf) at a constant slow speed of 3 to 7 cm (1.18 to 2.76 in.) per second.


      B200106E02


      Text in Illustration 
      *A
      Pressing Forward
      *B
      Pulling
      *1
      Non-padded Side
      *2
      Padded Side
      *3
      Squeegee
      *4
      Black Out Tape
      *5
      Release Paper
      -
      -
      *a
      Side View
      -
      -
      Reference Measurement 
      Area
      Measurement
      A
      10 to 20 mm (0.393 to 0.787 in.)
      B
      30 to 70 mm/sec. (1.18 to 2.76 in./sec.)
      C
      40 to 50° (for pressing forward)
      D
      30 to 45° (for pulling)

      NOTICE:
      Be sure to observe the specified pressing speed, force and angle of the squeegee to avoid wrinkles or air bubbles.

      HINT:
      1. Either angle of the squeegee (pressing forward or pulling) is acceptable.
      2. Be sure to apply the tape while removing the release paper 10 to 20 mm (0.394 to 0.787 in.) from the edge of the squeegee.



  1. Key points for installation of the tape (how to use a squeegee and installation procedure for hemmed surfaces)



      B147253E09
    1. If it is difficult to apply the tape, install it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.
      Text in Illustration 
      *1
      Squeegee
      *2
      Hem
      *a
      First
      *b
      Second
      *c
      Third

      HINT:
      When applying tape to the backside of a hem, remove the release paper and use your fingers or the padded surface of a squeegee.

  1. Key points for installation of the tape (how to use a squeegee and installation procedure for corners)

    1. Remove the release paper and apply the tape carefully with your fingers.

    2. Before applying the tape to each corner, heat the tape using a heat light and gradually apply it, avoiding wrinkles on the tape to achieve a neat finish.

  1. Check after installation

    1. After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, reapply using new tape.

      NOTICE:
      Do not reuse the tape.



2. INSTALL NO. 1 BLACK OUT TAPE


    B298009E01
  1. Remove the portion of the new No. 1 black out tape at the perforation as shown in the illustration.
    Text in Illustration 
    *A
    LH Side
    *B
    RH Side
    *a
    Perforation
    *b
    Remove
    *c
    Square
    *d
    Round



  1. Apply the new No. 1 black out tape to the positions shown in the illustration.


    B298006E01


    Text in Illustration 
    *1
    Edge of curved surface
    -
    -

    Standard Measurement:
    Dimension
    Measurement
    a
    - 1.0 to 1.0 mm (- 0.0394 to 0.0394 in.)
    b
    2.0 mm (0.0787 in.)
    c
    1.0 mm (0.0394 in.)
    d
    3.0 mm (0.118 in.)
    e
    3.0 mm (0.118 in.)



3. INSTALL FRONT DOOR GLASS RUN


    B307092
  1. Install the front door glass run.



4. INSTALL FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY
(Click here)