Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT DOOR BELT MOULDING

FRONT DOOR BELT MOULDING > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for both the RH and LH side.
  2. The procedure described below is for the LH side.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).



2. INSTALL FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY


    B298000
  1. Engage the guide and 5 claws to install the front door glass outer weatherstrip assembly.



3. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
  1. Connect the cable to the negative (-) auxiliary battery terminal and power window regulator master switch assembly and move the front door glass subassembly so that the door glass bolts can be seen.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal and power window regulator master switch.



    B307123
  1. Insert the front door glass sub-assembly into the front door panel along the front door glass run as shown in the illustration.

    NOTICE:
    Do not damage the front door glass.



    B307088
  1. Install the front door glass sub-assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B307087
  1. Install the front door No. 2 service hole cover.



4. INSTALL FRONT DOOR SERVICE HOLE COVER
  1. Apply new butyl tape to the front door panel.

  1. Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.



    B307124E01
  1. Attach the front door service hole cover according to the reference points on the front door panel.
    Text in Illustration 
    *a
    Reference Point

    HINT:
    Securely install the front door service hole cover preventing wrinkles and air bubbles.

  1. Connect the earth wire with the bolt.

    Torque:
    8.4 N*m{ 85 kgf*cm , 74 in.*lbf }



5. INSTALL DOOR SIDE AIRBAG SENSOR
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



  1. Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.


    B296255E01


    Text in Illustration 
    *a
    Incorrect
    *b
    Correct

  1. Insert the pin (stopper) into the door hole and install the door side airbag sensor to the front door panel with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    1. If the door side airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
    2. When installing the door side airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.
    3. Make sure that the pin (stopper) is securely inserted into the door hole.
    4. Tighten the bolt while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.



  1. Connect the connector to the door side airbag sensor.

    NOTICE:
    When connecting any airbag connector, take care not to damage the airbag wire harness.




    1. Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).


      H043305E12


      Text in Illustration 
      *1
      White Housing Lock
      *2
      Yellow CPA
      *a
      Connection is Completed
      -
      -

      HINT:
      When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and part (A), as it may result in an insecure fit.

  1. Check that there is no looseness in the installation parts of the door side airbag sensor.



6. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY
  1. Install the front No. 2 speaker assembly with the 2 screws.

    NOTICE:
    Do not touch the cone part of the speaker.

  1. Connect the connector.



7. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER
(Click here)


8. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here)



9. INSTALL FRONT FLOOR COVER RH
  1. Engage the 3 guides.



    B301488E01
  1. Engage the 3 clips <B> to install the front floor cover RH.

  1. Install the 2 clips <A>.



10. INITIALIZE POWER WINDOW CONTROL SYSTEM (for Driver Side)
(Click here)


11. INSPECT POWER WINDOW OPERATION
(Click here)


12. INSPECT SRS WARNING LIGHT
(Click here)