Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM

DTC    P0A7F-123    Hybrid Battery Pack Deterioration

for Preparation Click here


DESCRIPTION

The battery smart unit and the power management control ECU calculate the SOC (state of charge) of the HV battery through the accumulated amperage in the HV battery. The battery smart unit sends the condition of the HV battery to the power management control ECU. Then the power management control ECU calculates the SOC based on the information and controls HV battery charge and discharge according to the driving condition.

A171602E02


DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A7F
123
When either condition below is met:
  1. Resistance of an HV battery block exceeds the specified value.
    (1 trip detection logic)
  2. Difference in capacity between each battery block is larger than the standard.
    (2 trip detection logic)
  1. HV battery
  2. Battery smart unit

Related Data List 
DTC No.
Data List
P0A7F-123
  1. Internal Resistance R01 to R10
  2. Battery Block Vol -V01 to V10
  3. State of Charge (All Bat)
The following items can be helpful when performing repairs:
Data List
  1. Ready Signal
  2. Vehicle Spd
  3. Accelerator Degree
  4. Shift Sensor Shift Pos
  5. Engine Revolution
  6. Power Resource VB
  7. Batt Pack Current Val
  8. Auxiliary Battery Vol
  9. Battery Low Time
  10. DC Inhibit Time
  11. SOC after IG-ON
  12. Status of Charge Max
  13. Status of Charge Min
  14. Total Distance Traveled
  15. DTC Clear Run Distance
  16. Engine Run Time
Operation History Data
  1. Main Battery Low Voltage

HINT:
  1. For confirmation of this DTC output, it needs clearing DTCs and driving the vehicle for approximately 10 minutes. (As 2 trip detection logic is also used, check for DTCs including pending DTCs.)
  2. When the internal resistance of the HV battery increases, battery block voltage may drop.


MONITOR DESCRIPTION

  1. The battery smart unit calculates the resistance of the HV battery through amperage and voltage, and uses this resistance to determine the extent of deterioration of the HV battery. If the battery smart unit detects that the resistance of the HV battery has exceeded the standard, it determines that a malfunction has occurred. In addition, the battery smart unit monitors the SOC, and if the difference between the maximum and minimum each block SOC values exceeds the standard, it determines that a malfunction has occurred. When either of the malfunction detection conditions is met, the power management control ECU illuminates the MIL and set a DTC.

MONITOR STRATEGY


Related DTCs
P0A7F (INF 123): Battery cell malfunction
Required sensors / components
Main: Battery voltage sensor inside battery smart unit, battery current sensor
Sub: Battery temperature sensor
Frequency of operation
Continuous
Duration
TMC's intellectual property
MIL operation
TMC's intellectual property
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TMC's intellectual property
Other conditions belong to TMC's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


TMC's intellectual property
-

COMPONENT OPERATING RANGE


Battery smart unit
DTC P0A7F (INF 123) is not detected

CONFIRMATION DRIVING PATTERN


A308330E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for 30 seconds or more.
  5. Turn the ignition switch to ON (IG) and turn the Techstream on.
  6. Turn the ignition switch to ON (READY) and wait for 30 seconds or more.
  7. Drive the vehicle on urban roads at a speed of 40 km/h (25 mph) or more for a total of at least 10 minutes. [A]

    NOTICE:
    Avoid abrupt acceleration or braking.

  8. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Check that permanent DTCs are cleared. If no permanent DTC is output, the system is normal.
  11. If the permanent DTCs are not cleared, perform the universal trip, and then check for permanent DTCs again.

INSPECTION PROCEDURE

CAUTION:
When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

HINT:
After the repair, clear the DTCs, perform the following operations, and check that no DTCs (including pending DTCs) are output.
  1. Turn the ignition switch to ON (READY) and wait for 30 seconds or more.
    Drive the vehicle on urban road at a speed of 40 km/h (25 mph) or more for a total at least 10 minutes.
    (It is not necessary to maintain the vehicle speed at 40 km/h (25 mph) throughout the road test.)

    NOTICE:
    Avoid abrupt acceleration or braking.

    This DTC may not be stored if the vehicle is stopped or being driven at a constant speed.

1.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check and record any HV system DTCs, INF codes and freeze frame data.

  1. Read output DTCs (Click here).

    Result:
    Result
    Proceed to
    P0AFC-123 is not output.
    A
    P0AFC-123 is also output.
    B

  1. Turn the ignition switch off.

  1. Disconnect the Techstream from the DLC3.



B
GO TO DTC CHART (P0AFC-123) (Click here)
A


2.CHECK BATTERY SMART UNIT
  1. Ensure the safety of the areas in front and at the back of the vehicle.

  1. Apply the parking brake and secure the wheels using chocks.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (READY).

  1. Fully warm up the engine and turn the air conditioning off.

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / Battery block Vol - V01 to V10.

  1. Firmly depress the brake pedal with your left foot.

  1. Move the shift lever to D.

  1. Record each battery block voltage from the Data List "Battery Block Vol -V01 to V10" while fully depressing the accelerator pedal.



  1. Compare the battery block voltages "Battery Block Vol - V01 to V10" between the even and odd number groups in each combination shown in the table below.

    Table 1 
    Circuit A Battery Block
    Circuit B Battery Block
    Condition
    Battery Block Vol - V01 (VB1)
    Battery Block Vol - V02 (VB2)
    "Battery Block Vol - V01" - "Battery Block Vol - V02" = 0.3 V or more
    Battery Block Vol - V04 (VB4)
    Battery Block Vol - V03 (VB3)
    "Battery Block Vol - V04" - "Battery Block Vol - V03" = 0.3 V or more
    Battery Block Vol - V05 (VB5)
    Battery Block Vol - V06 (VB6)
    "Battery Block Vol - V05" - "Battery Block Vol - V06" = 0.3 V or more
    Battery Block Vol - V08 (VB8)
    Battery Block Vol - V07 (VB7)
    "Battery Block Vol - V08" - "Battery Block Vol - V07" = 0.3 V or more
    Battery Block Vol - V09 (VB9)
    Battery Block Vol - V10 (VB10)
    "Battery Block Vol - V09" - "Battery Block Vol - V10" = 0.3 V or more

    Table 2 
    Circuit A Battery Block
    Circuit B Battery Block
    Condition
    Battery Block Vol - V01 (VB1)
    Battery Block Vol - V02 (VB2)
    "Battery Block Vol - V02" - "Battery Block Vol - V01" = 0.3 V or more
    Battery Block Vol - V04 (VB4)
    Battery Block Vol - V03 (VB3)
    "Battery Block Vol - V03" - "Battery Block Vol - V04" = 0.3 V or more
    Battery Block Vol - V05 (VB5)
    Battery Block Vol - V06 (VB6)
    "Battery Block Vol - V06" - "Battery Block Vol - V05" = 0.3 V or more
    Battery Block Vol - V08 (VB8)
    Battery Block Vol - V07 (VB7)
    "Battery Block Vol - V07" - "Battery Block Vol - V08" = 0.3 V or more
    Battery Block Vol - V09 (VB9)
    Battery Block Vol - V10 (VB10)
    "Battery Block Vol - V10" - "Battery Block Vol - V09" = 0.3 V or more


    A298790E01


    A298791E01

    HINT:
    When an internal malfunction occurs in the battery smart unit, this symptom (difference in voltage of 0.3 V or more for all 5 pairs of blocks) will occur.

    Result:
    Result
    Proceed to
    All conditions in table 1 are met.
    A
    All conditions in table 2 are met.
    Other than above
    B

  1. Turn the ignition switch off.



B
REPLACE HV BATTERY (Click here)
A

REPLACE BATTERY SMART UNIT (Click here)