Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM

DTC    P0A80-123    Replace Hybrid Battery Pack

for Preparation Click here


DESCRIPTION

The HV battery uses nickel metal-hydride batteries. The power management control ECU controls the SOC (state of charge) of the HV battery at a constant level during driving. The HV battery is composed of 20 modules, and each module consists of six 1.2 V cells in series. The battery smart unit monitors battery block voltage at 10 locations. Each battery block is composed of 2 modules in a set.

A173707E15


A298790E01


DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A80
123
Voltage difference between battery blocks is larger than the specified value due to an internal malfunction of the HV battery.
(2 trip detection logic)
  1. HV battery
  2. Battery smart unit

Related Data List 
DTC No.
Data List
P0A80-123
  1. Battery Block Vol -V01 to V10
  2. State of Charge (All Bat)
The following items can be helpful when performing repairs:
Data List
  1. Ready Signal
  2. Vehicle Spd
  3. Accelerator Degree
  4. Shift Sensor Shift Pos
  5. Engine Revolution
  6. Internal Resistance R01 to R10
  7. Power Resource VB
  8. Batt Pack Current Val
  9. Auxiliary Battery Vol
  10. Battery Low Time
  11. DC Inhibit Time
  12. SOC after IG-ON
  13. Status of Charge Max
  14. Status of Charge Min
  15. Total Distance Traveled
  16. DTC Clear Run Distance
  17. Engine Run Time
Operation History Data
  1. Main Battery Low Voltage

HINT:
  1. This DTC can be stored after clearing DTCs and driving the vehicle for approximately 10 minutes. (As 2 trip detection logic is used, check for DTCs including pending DTCs.)
  2. DTC P0A80-123 is stored when a malfunction is detected in the HV battery or battery smart unit. If the HV supply battery is malfunctioning, the malfunction may not be reproduced when the condition of the HV supply battery changes due to difference in driving load (amperage), battery SOC and battery temperature. Therefore, use the freeze frame data when performing a repair.
    1. When the HV battery is malfunctioning:
      1. - Voltage of 1 or a few battery blocks has dropped. (voltage difference from that of the next block is 1 V or more.)
      2. - Voltage of all battery blocks is output randomly with no certain pattern.
    1. When the battery smart unit is malfunctioning:
      1. - Differences in battery block voltages have a certain pattern.


MONITOR DESCRIPTION

The battery smart unit, which monitors the voltage of the battery blocks, determines that malfunction has occurred if a voltage difference between the battery blocks exceeds the standard. When the malfunction detection condition is satisfied, the power management control ECU will illuminates the MIL and set a DTC.

MONITOR STRATEGY


Related DTCs
P0A80 (INF 123): Battery cell malfunction
Required sensors / components
Main: Battery voltage sensor inside battery smart unit
Sub: Battery current sensor, battery temperature sensor
Frequency of operation
Continuous
Duration
TMC's intellectual property
MIL operation
TMC's intellectual property
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TMC's intellectual property
Other conditions belong to TMC's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


TMC's intellectual property
-

COMPONENT OPERATING RANGE


Battery smart unit
DTC P0A80 (INF 123) is not detected

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for 30 seconds or more.
  5. Turn the ignition switch to ON (IG) and turn the Techstream on.
  6. Turn the ignition switch to ON (READY).
  7. Perform a universal trip.
  8. With the shift lever in N, leave the vehicle until SOC drops to 30 %.

    HINT:
    Although DTC P3000 (INF 388) may be stored if the SOC drops to 20 % or lower, this is not a malfunction.

  9. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
  10. Read the current DTCs.

    HINT:
    1. If a current DTC is output, the system is malfunctioning.
    2. If a current DTC is not output, perform the following procedure.

  11. Check that permanent DTCs are cleared. If no permanent DTC is output, the system is normal.

INSPECTION PROCEDURE

CAUTION:
When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

1.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check and record any HV system DTCs, INF codes and freeze frame data.

  1. Read output DTCs (Click here).

    Result:
    Result
    Proceed to
    P0AFC-123 is not output.
    A
    P0AFC-123 is also output.
    B

  1. Turn the ignition switch off.

  1. Disconnect the Techstream from the DLC3.



B
GO TO DTC CHART (P0AFC-123) (Click here)
A


2.CHECK BATTERY SMART UNIT
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Read output DTCs.

  1. Using the Techstream, make a note of the freeze frame data item "Battery Block Vol -V01 to V10".



  1. Compare the freeze frame data item "Battery Block Vol - V01 to V10" values with those shown in the following combination tables.

    Table 1 
    Circuit A Battery Block
    Circuit B Battery Block
    Condition
    Battery Block Vol - V01 (VB1)
    Battery Block Vol - V02 (VB2)
    "Battery Block Vol - V01" - "Battery Block Vol - V02" = 0.3 V or more
    Battery Block Vol - V04 (VB4)
    Battery Block Vol - V03 (VB3)
    "Battery Block Vol - V04" - "Battery Block Vol - V03" = 0.3 V or more
    Battery Block Vol - V05 (VB5)
    Battery Block Vol - V06 (VB6)
    "Battery Block Vol - V05" - "Battery Block Vol - V06" = 0.3 V or more
    Battery Block Vol - V08 (VB8)
    Battery Block Vol - V07 (VB7)
    "Battery Block Vol - V08" - "Battery Block Vol - V07" = 0.3 V or more
    Battery Block Vol - V09 (VB9)
    Battery Block Vol - V10 (VB10)
    "Battery Block Vol - V09" - "Battery Block Vol - V10" = 0.3 V or more

    Table 2 
    Circuit A Battery Block
    Circuit B Battery Block
    Condition
    Battery Block Vol - V01 (VB1)
    Battery Block Vol - V02 (VB2)
    "Battery Block Vol - V02" - "Battery Block Vol - V01" = 0.3 V or more
    Battery Block Vol - V04 (VB4)
    Battery Block Vol - V03 (VB3)
    "Battery Block Vol - V03" - "Battery Block Vol - V04" = 0.3 V or more
    Battery Block Vol - V05 (VB5)
    Battery Block Vol - V06 (VB6)
    "Battery Block Vol - V06" - "Battery Block Vol - V05" = 0.3 V or more
    Battery Block Vol - V08 (VB8)
    Battery Block Vol - V07 (VB7)
    "Battery Block Vol - V07" - "Battery Block Vol - V08" = 0.3 V or more
    Battery Block Vol - V09 (VB9)
    Battery Block Vol - V10 (VB10)
    "Battery Block Vol - V10" - "Battery Block Vol - V09" = 0.3 V or more


    A298791E01

    HINT:
    When an internal malfunction occurs in the battery smart unit, this symptom (difference in voltage of 0.3 V or more for all 5 pairs of blocks) will occur.

    Result:
    Result
    Proceed to
    All conditions in table 1 are met.
    A
    All conditions in table 2 are met.
    Other than above
    B

  1. Turn the ignition switch off.



B
REPLACE HV BATTERY (Click here)
A

REPLACE BATTERY SMART UNIT (Click here)