Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

AIR CONDITIONING SYSTEM > TERMINALS OF ECU

for Preparation Click here



AIR CONDITIONING AMPLIFIER ASSEMBLY

E226604E14

HINT:
Check from the rear of the connector while it is connected to the air conditioning amplifier assembly.


Terminal No.
(Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
G34-1 (IG+) - G34-14 (GND)
V - W-B
Power source (IG)
Ignition switch ON (IG)
11 to 14 V
G34-1 (IG+) - G34-14 (GND)
V - W-B
Power source (IG)
Ignition switch off
Below 1 V
G34-3 (PTC3) - G34-14 (GND)*1
R - W-B
Quick heater operation signal
  1. Ignition switch ON (READY)
  2. ECO mode switch (eco switch assembly) off
  3. Blower motor on
  4. Temperature settings: MAX HOT
  5. Engine coolant temperature approximately 50°C lower
  6. Ambient temperature 10°C or lower
  7. IDH terminal signal less than 1 V (Inverter with converter assembly overload not detected)
Below 1 V
G34-4 (ECOS) - G34-14 (GND)
R - W-B
ECO mode switch (eco switch assembly) signal
  1. Ignition switch ON (IG)
  2. ECO mode switch (eco switch assembly): on
Below 1 V
G34-4 (ECOS) - G34-14 (GND)
R - W-B
ECO mode switch (eco switch assembly) signal
  1. Ignition switch ON (IG)
  2. ECO mode switch (eco switch assembly): off
11 to 14 V
G34-5 (TAM) - G34-13 (SG-2)
W - B
Ambient temperature sensor signal
  1. Ignition switch ON (IG)
  2. Ambient temperature: 25°C (77°F)
1.8 to 2.2 V
G34-5 (TAM) - G34-13 (SG-2)
W - B
Ambient temperature sensor signal
  1. Ignition switch ON (IG)
  2. Ambient temperature: 40°C (104°F)
0.9 to 1.2 V
G34-9 (PRE) - G34-13 (SG-2)
GR - B
Air conditioning pressure sensor signal
  1. Ignition switch ON (READY)
  2. A/C system operating
  3. Refrigerant pressure: Abnormal pressure (more than 3025 kPa (30.8 kgf/cm2, 439 psi))
4.62 V or higher
G34-9 (PRE) - G34-13 (SG-2)
GR - B
Air conditioning pressure sensor signal
  1. Ignition switch ON (READY)
  2. A/C system operating
  3. Refrigerant pressure: Abnormal pressure (less than 176 kPa (1.8 kgf/cm2, 25 psi))
Below 0.74 V
G34-9 (PRE) - G34-13 (SG-2)
GR - B
Air conditioning pressure sensor signal
  1. Ignition switch ON (READY)
  2. A/C system operating
  3. Refrigerant pressure: Normal pressure (less than 3025 kPa (30.8 kgf/cm2, 439 psi) and more than 176 kPa (1.8 kgf/cm2, 25 psi))
0.74 to 4.62 V
G34-10 (S5-3) - G34-13 (SG-2)
Y - B
Power supply for air conditioning pressure sensor
Ignition switch ON (IG)
4.75 to 5.25 V
G34-10 (S5-3) - G34-13 (SG-2)
Y - B
Power supply for air conditioning pressure sensor
Ignition switch off
Below 1 V
G34-11 (CANH) - G34-12 (CANL)
V - W
CAN communication system
CAN communication occurring
Pulse generation
G34-13 (SG-2) - Body ground
B - Body ground
Ground for air conditioning pressure sensor, ambient temperature sensor
Always
Below 1 V
G34-14 (GND) - Body ground
W-B - Body ground
Ground for main power supply
Always
Below 1 V
G34-21 (B) - G34-14 (GND)
BE - W-B
Power source (Back-up)
Ignition switch off
11 to 14 V
G34-22 (BLW) - G34-14 (GND)
R - W-B
Blower motor speed control signal
  1. Ignition switch ON (IG)
  2. Blower switch: LO
Pulse generation
(See waveform 1)
G34-27 (IDH) - G34-14 (GND)*1
L - W-B
Inverter with converter assembly current over signal
Ignition switch ON (IG) (inverter with converter assembly overload not detected)
less than 1 V
G34-29 (TR) - G34-34 (SG-1)
P - SB
Room temperature sensor signal
  1. Ignition switch ON (IG)
  2. Cabin temperature: 25°C (77°F)
1.8 to 2.2 V
G34-29 (TR) - G34-34 (SG-1)
P - SB
Room temperature sensor signal
  1. Ignition switch ON (IG)
  2. Cabin temperature: 40°C (104°F)
1.2 to 1.6 V
G34-30 (S5-4) - G34-14 (GND)
R - W-B
Power supply for solar sensor
Ignition switch ON (IG)
4.75 to 5.25 V
G34-30 (S5-4) - G34-14 (GND)
R - W-B
Power supply for solar sensor
Ignition switch off
Below 1 V
G34-33 (TS) - G34-14 (GND)
V - W-B
Solar sensor signal
  1. Ignition switch ON (IG)
  2. Solar sensor subjected to electric light
0.8 to 4.3 V
G34-33 (TS) - G34-14 (GND)
V - W-B
Solar sensor signal
  1. Ignition switch ON (IG)
  2. Solar sensor covered with a cloth
Below 0.8 V
G34-34 (SG-1) - Body ground
SB - Body ground
Ground for room temperature sensor
Always
Below 1 V
G34-37 (LIN1) - G34-14 (GND)
LG - W-B
LIN communication signal
Ignition switch ON (IG)
Pulse generation
G34-39 (PTC2) - G34-14 (GND)*1
BR - W-B
Quick heater operation signal
  1. Ignition switch ON (READY)
  2. ECO mode switch (eco switch assembly) off
  3. Blower motor on
  4. Temperature settings: MAX HOT
  5. Engine coolant temperature approximately 50°C lower
  6. Ambient temperature 10°C or lower
  7. IDH terminal signal less than 1 V (Inverter with converter assembly overload not detected)
Below 1 V
G34-40 (PTC1) - G34-14 (GND)*1
V - W-B
Quick heater operation signal
  1. Ignition switch ON (READY)
  2. ECO mode switch (eco switch assembly) off
  3. Blower motor on
  4. Temperature settings: MAX HOT
  5. Engine coolant temperature approximately 50°C or lower
  6. Ambient temperature 10°C or lower
  7. IDH terminal signal less than 1 V (Inverter with converter assembly overload not detected)
Below 1 V
z1-2 (BUS G) - Body ground
-
Ground for BUS IC
Always
Below 1 V
z1-3 (BUS) - z1-2 (BUS G)
-
BUS IC control signal
Ignition switch ON (IG)
Pulse generation
z1-4 (B BUS) - z1-2 (BUS G)
-
Power supply for BUS IC
Ignition switch off
11 to 14 V
z1-5 (SGA) - Body ground
-
Ground for evaporator temperature sensor
Always
Below 1 V
z1-6 (TEA) - z1-5 (SGA)
-
Evaporator temperature sensor signal
  1. Ignition switch ON (IG)
  2. Evaporator temperature: 0°C (32°F)
2.0 to 2.4 V
z1-6 (TEA) - z1-5 (SGA)
-
Evaporator temperature sensor signal
  1. Ignition switch ON (IG)
  2. Evaporator temperature: 15°C (59°F)
1.4 to 1.8 V
  1. *1: w/ Quick Heater Assembly


    E103396E01
  1. Waveform 1:
    Item
    Content
    Terminal No.
    G34-22 (BLW) - G34-14 (GND)
    Tool Setting
    1 V/DIV., 500 μs/DIV.
    Vehicle Condition
    Power switch on (IG)
    Blower switch: LO


AIR CONDITIONING PANEL (HEATER CONTROL SWITCH BOARD)

E238083E01

HINT:
Check from the rear of the connector while it is connected to the air conditioning panel (heater control switch board).


Terminal No.
(Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
G33-2 (LIN1) - Body ground
LG - Body ground
LIN communication signal
Ignition switch ON (IG)
Pulse generation
G33-3 (SWO) - G33-8 (GND)
G - W-B
Steering pad switch assembly signal
Ignition switch off
Below 1 V
G33-3 (SWO) - G33-8 (GND)
G - W-B
Steering pad switch assembly signal
Ignition switch ON (IG)
4.5 to 5.5 V
G33-5 (IG+) - G33-8 (GND)
V - W-B
Power source (IG)
Ignition switch off
Below 1 V
G33-5 (IG+) - G33-8 (GND)
V - W-B
Power source (IG)
Ignition switch ON (IG)
11 to 14 V
G33-6 (ILL+) - Body ground
R - Body ground
Illumination signal
Light control switch off
Below 1 V
G33-6 (ILL+) - Body ground
R - Body ground
Illumination signal
Light control switch tail or head position
11 to 14 V
G33-7 (ILL-) - Body ground
W - Body ground
Illumination signal
Light control switch off
Below 1 V
G33-7 (ILL-) - Body ground
W - Body ground
Illumination signal
Light control switch tail or head position
Pulse generation
G33-8 (GND) - Body ground
W-B - Body ground
Ground for air conditioning panel (heater control switch board)
Always
Below 1 V

POWER MANAGEMENT CONTROL ECU (Click here)

INVERTER WITH CONVERTER ASSEMBLY (Click here)