Home › Engine / Hybrid System › 1NZ-FXE ENGINE MECHANICAL › CYLINDER HEAD GASKET

CYLINDER HEAD GASKET > REMOVAL

for Preparation Click here



1. REMOVE TIMING CHAIN COVER
(Click here)


2. REMOVE INTAKE MANIFOLD STAY


    A268286
  1. Remove the 2 bolts and intake manifold stay.



3. REMOVE INTAKE MANIFOLD


    A267685
  1. Disconnect the 4 wire harness clamps and water by-pass hose.



    A267684
  1. Disconnect the fuel vapor feed hose and ventilation hose.



    A268526
  1. Remove the 3 bolts, 2 nuts and intake manifold.



    A268531
  1. Remove the ventilation hose.



    A268529
  1. Remove the bolt and intake manifold insulator.



    A268530
  1. Remove the No. 1 intake manifold to head gasket.



4. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    A267688
  1. Remove the 3 bolts and No. 1 exhaust manifold heat insulator.



5. REMOVE MANIFOLD SUPPORT BRACKET


    A267692
  1. Remove the 4 bolts and manifold support bracket.



6. REMOVE EXHAUST MANIFOLD


    A268068
  1. Disconnect the wire harness clamp and oxygen sensor connector.



    A267694
  1. Remove the 3 bolts, 2 nuts and exhaust manifold.

  1. Remove the exhaust manifold to head gasket.



7. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY


    A156304E01
  1. Turn the stopper plate of the No. 1 chain tensioner assembly clockwise and push in the plunger with the lock released.
    Text in Illustration 
    *1
    Hexagon Wrench
    *2
    Plunger
    *3
    Stopper Plate

  1. Turn the stopper plate of the No. 1 chain tensioner assembly counterclockwise and insert a hexagon wrench into the hole in the stopper plate to lock with the plunger pushed in.



    A116568
  1. Remove the 2 bolts and No. 1 chain tensioner assembly.

    NOTICE:
    Do not rotate the crankshaft with the No. 1 chain tensioner removed.



8. REMOVE CHAIN TENSIONER SLIPPER


    A265765
  1. Remove the chain tensioner slipper.



9. REMOVE NO. 1 CHAIN VIBRATION DAMPER


    A265766
  1. Remove the 2 bolts and No. 1 chain vibration damper.



10. REMOVE CHAIN SUB-ASSEMBLY


    A265767
  1. Remove the chain sub-assembly.

    NOTICE:
    When rotating the camshaft with the chain sub-assembly removed, rotate the crankshaft counterclockwise 40° from TDC and align the oil jet hole with the paint mark to prevent the pistons from coming into contact with the valves.



11. REMOVE CAMSHAFT


    A268214E01
  1. Using several steps, uniformly loosen and remove the 19 bolts in the sequence shown in the illustration, then remove the No. 1 camshaft bearing cap and 8 No. 2 camshaft bearing caps.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.

  1. Remove the camshaft and No. 2 camshaft.



12. REMOVE CYLINDER HEAD SUB-ASSEMBLY


    A267008E01
  1. Using several steps, uniformly loosen and remove the 10 cylinder head bolts and 10 washers with an 8 mm bi-hexagon wrench in the sequence shown in the illustration.

    NOTICE:
    1. When removing the cylinder head bolt, do not drop the washer into the cylinder head sub-assembly.
    2. Removing the bolts in the wrong order may cause damage to the cylinder head sub-assembly.

  1. Remove the cylinder head sub-assembly.



13. REMOVE CYLINDER HEAD GASKET


    A268213
  1. Remove the cylinder head gasket from the cylinder block.