Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A7A-518    Generator Inverter Performance

DTC    P0A7A-811    Generator Inverter Performance

for Preparation Click here


DESCRIPTION

For a description of the inverter .
If an abnormal amount of current flows through the generator inverter, the MG ECU detects it and sends a signal to inform the power management control ECU of the malfunction.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A7A
518
Generator inverter fail signal detection (hybrid vehicle transaxle assembly malfunction)
Overcurrent occurs in the generator inverter.*
(1 trip detection logic)
  1. Inverter with converter assembly
  2. Hybrid vehicle transaxle assembly
  3. Wire harness or connector
811
Abnormal generator inverter current (overcurrent) detection (hybrid vehicle transaxle assembly malfunction)
(1 trip detection logic)
  1. *: The hybrid vehicle transaxle assembly may be suspected as a main cause of the malfunction.

MONITOR DESCRIPTION

P0A7A (INF 518):
If excessive amperage flows through the generator inverter, the generator inverter will transmit an inverter fail signal to the MG ECU. Upon receiving this signal, the power management control ECU will illuminate the MIL and set a DTC.
P0A7A (INF 811):
If the MG ECU detects that the generator inverter current exceeds the threshold level for a period of time, the power management control ECU will illuminate the MIL and set a DTC.

MONITOR STRATEGY


Related DTCs
P0A7A (INF 518): GFIV detection (Over current malfunction)
P0A7A (INF 811): Generator inverter abnormal current
Required sensors / components
Generator inverter
Frequency of operation
Continuous
Duration
TMC's intellectual property
MIL operation
1 driving cycle
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TMC's intellectual property
Other conditions belong to TMC's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


TMC's intellectual property
-

COMPONENT OPERATING RANGE


Power management control ECU
DTC P0A7A (INF 518/811) is not detected

CONFIRMATION DRIVING PATTERN


A308311E09

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for 30 seconds or more.
  5. Turn the ignition switch to ON (IG) and turn the Techstream on.
  6. Turn the ignition switch to ON (READY).
  7. With the shift lever in P, wait for 5 seconds. [A]

    HINT:
    Check that there are no abnormalities (abnormal sounds, coolant leaks, DTC output, etc.)

  8. Drive the vehicle approximately 10 minutes mainly using the engine. [B]
    (DTC P0A7A-811 is stored when the engine is cranked with the shift lever in P.)
  9. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes. [C]
  10. Read the current DTCs.

    HINT:
    1. If a current DTC is output, the system is malfunctioning.
    2. If a current DTC is not output, perform the following procedure.

  11. Check that permanent DTCs are cleared. If no permanent DTC is output, the system is normal.
  12. If the permanent DTCs are not cleared, perform a universal trip, and then check for permanent DTCs again.

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A1A-200 .

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (Click here).

    HINT:
    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Turn the ignition switch to ON (READY) and wait for 5 seconds or more.
  2. Drive the vehicle for approximately 10 minutes mainly using the engine.

1.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P0A7A-203 is not output.
    A
    P0A7A-203 is also output.
    B

    NOTICE:
    1. If P0A7A-203 is output, troubleshoot it first. After completing the troubleshooting for P0A7A-203, return to perform troubleshooting for this DTC.
    2. Parts repaired or replaced during troubleshooting for P0A7A-203 do not need to be re-inspected in this diagnosis procedure.

  1. Turn the ignition switch off.



B
GO TO DTC CHART (P0A7A-203) (Click here)
A


2.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    HINT:
    1. If P0A7A-203 was not output in step 1 of this diagnosis procedure, check Table 1 below.
    2. If P0A7A-203 was output in step 1 of this diagnosis procedure, repair that DTC first, then check Table 2 below.

    Result:
    Result
    Proceed to
    Only P0A7A-518 or 811 is output or DTCs other than the ones in the table below are also output.
    A
    Any of the following DTCs are also output.
    B


    Table 1 
    DTC No.
    Relevant Diagnosis
    P0A1A (all INF codes)*1
    Generator Control Module
    P0A1B (all INF codes)*1
    Drive Motor "A" Control Module
    P0A1D (all INF codes)*1
    Hybrid Powertrain Control Module
    P0A3F-243
    Drive Motor "A" Position Sensor Circuit
    P0A40-500
    Drive Motor "A" Position Sensor Circuit Range/Performance
    P0A41-245
    Drive Motor "A" Position Sensor Circuit Low
    P0A4B-253
    Generator Position Sensor Circuit
    P0A4C-513
    Generator Position Sensor Circuit Range/Performance
    P0A4D-255
    Generator Position Sensor Circuit Low
    P0A60 (all INF codes)*1
    Drive Motor "A" Phase V Current
    P0A63 (all INF codes)*1
    Drive Motor "A" Phase W Current
    P0A72 (all INF codes)*1
    Generator Phase V Current
    P0A75 (all INF codes)*1
    Generator Phase W Current
    P0A78-266, 267, 586
    Drive Motor "A" Inverter Performance
    P0A94-585, 587, 589, 590
    DC/DC Converter Performance
    P0C76-523
    Hybrid Battery System Discharge Time Too Long

    Table 2 
    DTC No.
    Relevant Diagnosis
    P0A1A (all INF codes)*1
    Generator Control Module
    P0A1B (all INF codes)*1
    Drive Motor "A" Control Module
    P0A1D (all INF codes)*1
    Hybrid Powertrain Control Module
    P0A3F-243
    Drive Motor "A" Position Sensor Circuit
    P0A40-500
    Drive Motor "A" Position Sensor Circuit Range/Performance
    P0A41-245
    Drive Motor "A" Position Sensor Circuit Low
    P0A4B-253
    Generator Position Sensor Circuit
    P0A4C-513
    Generator Position Sensor Circuit Range/Performance
    P0A4D-255
    Generator Position Sensor Circuit Low
    P0A60 (all INF codes)*1
    Drive Motor "A" Phase V Current
    P0A63 (all INF codes)*1
    Drive Motor "A" Phase W Current
    P0A72-333
    Generator Phase V Current
    P0A75-341
    Generator Phase W Current
    P0A78-266, 267, 586
    Drive Motor "A" Inverter Performance
    P0A94-585, 587, 589, 590
    DC/DC Converter Performance
    P0C76-523
    Hybrid Battery System Discharge Time Too Long

    HINT:
    1. *1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.
    2. P0A7A-518 may be set due to a malfunction which also causes DTCs in the preceding table to be set. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a test to attempt to reproduce the problems, and check that no DTCs are output.

  1. Turn the ignition switch off.



B
GO TO DTC CHART (HYBRID CONTROL SYSTEM) (Click here)
A


3.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



    A267460
  1. Check the connector connections and contact pressure of the low voltage connectors of the inverter with converter assembly (Click here).

    NOTICE:
    Before disconnecting the connector, confirm that it is properly connected by checking that the locking claws are engaged and that the connector does not pull out.

    OK:
    The connectors are connected securely and there are no contact pressure problems.

    HINT:
    When connecting the connector, insert it with the locking lever in the raised position. Rotate the lever downward and make sure that the connector is pulled into its socket. When the locking lever is in its fully closed position, a click will be heard as its locking claws engage. After the click is heard, pull up on the connector to confirm that it is properly connected.



NG
CONNECT SECURELY
OK


4.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Disconnect connector C28 from the inverter with converter assembly.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the ignition switch to ON (IG).



    A217747E15
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C28-11 (GRF) - Body ground
    Ignition switch ON (IG)
    Below 1 V
    C28-12 (GRFG) - Body ground
    Ignition switch ON (IG)
    Below 1 V
    C28-7 (GSN) - Body ground
    Ignition switch ON (IG)
    Below 1 V
    C28-8 (GSNG) - Body ground
    Ignition switch ON (IG)
    Below 1 V
    C28-10 (GCS) - Body ground
    Ignition switch ON (IG)
    Below 1 V
    C28-9 (GCSG) - Body ground
    Ignition switch ON (IG)
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Inverter with Converter Assembly)

    NOTICE:
    Turning the ignition switch to ON (IG) with the low voltage connector of the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Connect the inverter with converter assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK GENERATOR RESOLVER

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Disconnect connector C28 from the inverter with converter assembly.



    A217747E15
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    C28-11 (GRF) - C28-12 (GRFG)
    Ignition switch off
    7.1 to 21.6 Ω
    C28-7 (GSN) - C28-8 (GSNG)
    Ignition switch off
    13.7 to 34.5 Ω
    C28-10 (GCS) - C28-9 (GCSG)
    Ignition switch off
    12.8 to 32.4 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    C28-11 (GRF) or C28-12 (GRFG) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher
    C28-7 (GSN) or C28-8 (GSNG) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher
    C28-10 (GCS) or C28-9 (GCSG) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Inverter with Converter Assembly)

  1. Connect the inverter with converter assembly connector.



NG
Go to step 10
OK


6.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Disconnect connector C28 from the inverter with converter assembly.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the ignition switch to ON (IG).



    A217747E16
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C28-1 (MRF) - Body ground
    Ignition switch ON (IG)
    Below 1 V
    C28-2 (MRFG) - Body ground
    Ignition switch ON (IG)
    Below 1 V
    C28-3 (MSN) - Body ground
    Ignition switch ON (IG)
    Below 1 V
    C28-4 (MSNG) - Body ground
    Ignition switch ON (IG)
    Below 1 V
    C28-6 (MCS) - Body ground
    Ignition switch ON (IG)
    Below 1 V
    C28-5 (MCSG) - Body ground
    Ignition switch ON (IG)
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Inverter with Converter Assembly)

    NOTICE:
    Turning the ignition switch to ON (IG) with the low voltage connector of the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Connect the inverter with converter assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK MOTOR RESOLVER

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Disconnect connector C28 from the inverter with converter assembly.



    A217747E16
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    C28-1 (MRF) - C28-2 (MRFG)
    Ignition switch off
    7.1 to 21.6 Ω
    C28-3 (MSN) - C28-4 (MSNG)
    Ignition switch off
    13.7 to 34.5 Ω
    C28-6 (MCS) - C28-5 (MCSG)
    Ignition switch off
    12.8 to 32.4 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    C28-1 (MRF) or C28-2 (MRFG) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher
    C28-3 (MSN) or C28-4 (MSNG) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher
    C28-6 (MCS) or C28-5 (MCSG) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Inverter with Converter Assembly)

  1. Connect the inverter with converter assembly connector.



NG
Go to step 12
OK


8.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)


    A267571
  1. Check the connection of the generator resolver connector.

    OK:
    The connector is connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK


9.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)


    A267572
  1. Check the connection of the motor resolver connector.

    OK:
    The connector is connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)  

10.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)


    A267571
  1. Check the connection of the generator resolver connector.

    OK:
    The connector is connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK


11.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Disconnect connector C28 from the inverter with converter assembly.



    A268860E02
  1. Disconnect the generator resolver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    C28-11 (GRF) - C24-1 (GRF)
    Ignition switch off
    Below 1 Ω
    C28-12 (GRFG) - C24-5 (GRFG)
    Ignition switch off
    Below 1 Ω
    C28-7 (GSN) - C24-2 (GSN)
    Ignition switch off
    Below 1 Ω
    C28-8 (GSNG) - C24-6 (GSNG)
    Ignition switch off
    Below 1 Ω
    C28-10 (GCS) - C24-3 (GCS)
    Ignition switch off
    Below 1 Ω
    C28-9 (GCSG) - C24-7 (GCSG)
    Ignition switch off
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    C28-11 (GRF) or C24-1 (GRF) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher
    C28-12 (GRFG) or C24-5 (GRFG) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher
    C28-7 (GSN) or C24-2 (GSN) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher
    C28-8 (GSNG) or C24-6 (GSNG) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher
    C28-10 (GCS) or C24-3 (GCS) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher
    C28-9 (GCSG) or C24-7 (GCSG) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Inverter with Converter Assembly)
    *b
    Front view of wire harness connector
    (to Generator Resolver)

    HINT:
    The generator resolver is not available separately. If it requires replacement, replace the hybrid vehicle transaxle assembly.

  1. Connect the generator resolver connector.

  1. Connect the inverter with converter assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY (Click here)  

12.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)


    A267572
  1. Check the connection of the motor resolver connector.

    OK:
    The connector is connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK


13.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Disconnect connector C28 from the inverter with converter assembly.



    A268861E02
  1. Disconnect the motor resolver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    C28-1 (MRF) - C26-3 (MRF)
    Ignition switch off
    Below 1 Ω
    C28-2 (MRFG) - C26-6 (MRFG)
    Ignition switch off
    Below 1 Ω
    C28-3 (MSN) - C26-1 (MSN)
    Ignition switch off
    Below 1 Ω
    C28-4 (MSNG) - C26-4 (MSNG)
    Ignition switch off
    Below 1 Ω
    C28-6 (MCS) - C26-2 (MCS)
    Ignition switch off
    Below 1 Ω
    C28-5 (MCSG) - C26-5 (MCSG)
    Ignition switch off
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    C28-1 (MRF) or C26-3 (MRF) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher
    C28-2 (MRFG) or C26-6 (MRFG) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher
    C28-3 (MSN) or C26-1 (MSN) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher
    C28-4 (MSNG) or C26-4 (MSNG) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher
    C28-6 (MCS) or C26-2 (MCS) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher
    C28-5 (MCSG) or C26-5 (MCSG) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Inverter with Converter Assembly)
    *b
    Front view of wire harness connector
    (to Motor Resolver)

    HINT:
    The motor resolver is not available separately. If it requires replacement, replace the hybrid vehicle transaxle assembly.

  1. Connect the motor resolver connector.

  1. Connect the inverter with converter assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY (Click here)