Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

DTC    B1500    Fuel Sender Open Detected

for Preparation Click here


DESCRIPTION

This DTC is stored when the combination meter assembly detects a fuel sender gauge malfunction via a direct line.

DTC No.
DTC Detection Condition
Trouble Area
B1500
When IG voltage is 9.5 V or more and the following condition is detected:
  1. Fuel sender gauge operation malfunction
  1. Harness or connector
  2. Fuel sender gauge assembly
  3. Combination meter assembly

WIRING DIAGRAM


E237325E01


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (FUEL INPUT)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Combination Meter / Data List.

  1. Check the values by referring to the table below.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Fuel Input
    Fuel input/Min.: 0, Max.: 127.5
    10th segment comes on: 31.7 to 36.0
    Unit: Liter
    9th segment comes on: 28.3 to 31.7
    8th segment comes on: 25.0 to 28.3
    7th segment comes on: 21.6 to 25.0
    6th segment comes on: 18.2 to 21.6
    5th segment comes on: 14.8 to 18.2
    4th segment comes on: 11.5 to 14.8
    3rd segment comes on: 8.1 to 11.5
    2nd segment comes on: 4.7 to 8.1
    1st segment comes on: 3.8 to 4.7

    Result:

    Result
    Proceed to
    Fuel level data can be displayed on the Techstream and DTC B1500 is output.
    A
    Fuel level data cannot be displayed on the Techstream.
    B



B
Go to step 2
A

REPLACE COMBINATION METER ASSEMBLY (Click here)  

2.INSPECT FUEL SENDER GAUGE ASSEMBLY


    E160303E96
  1. Disconnect the G1 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G1-2 (L) - Body ground
    Always
    13.5 to 415.5 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly)



NG
Go to step 3
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SENDER GAUGE ASSEMBLY)
  1. Disconnect the M22 fuel sender gauge assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G1-2 (L) - M22-2 (FS)
    Always
    Below 1 Ω
    G1-2 (L) - Body ground
    Always
    10 kΩ or higher
    M22-3 (FE)- Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT FUEL SENDER GAUGE ASSEMBLY


    A307401E01
  1. Remove the fuel sender gauge assembly (Click here).

  1. Check that the float moves smoothly between E and F.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Float level is F (upper)
    13.5 to 16.5 Ω
    1 - 2
    Float level is between F (upper) and E (lower)
    13.5 to 415.5 Ω (Gradually changes)
    1 - 2
    Float level is E (lower)
    405.5 to 414.5 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Sender Gauge Assembly)



NG
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
OK


5.CHECK FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE
  1. Visually check for deformation on the fuel suction tube assembly with pump and gauge connector.

    OK:
    There is no deformation.



NG
REPLACE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE (Click here)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)