Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM (for Entry Function)

SMART KEY SYSTEM (for Entry Function) > All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate

for Preparation Click here


DESCRIPTION

When the entry operation and wireless operation of the door lock functions do not operate, a malfunction or wave interference may be occurring in either of the following: 1) the signal communication line between the door control & tire pressure monitoring and certification ECU (smart key ECU assembly) (the line used for entry and wireless operations); or 2) the electrical key transmitter sub-assembly. If the entry lock and wireless lock operations cannot be performed, there may be electrical key transmitter sub-assembly malfunctions, wave interference or problems in the communication which is used for the entry and wireless function between the door control & tire pressure monitoring and certification ECU (smart key ECU assembly).

WIRING DIAGRAM


B309661E01


INSPECTION PROCEDURE

NOTICE:
  1. The smart key system (for Entry Function) uses the CAN communication system and LIN communication system. First inspect the communication systems by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart key system (for Entry Function) after confirming that the communication systems are functioning properly.
  2. When using the Techstream with the power switch off to troubleshoot:
    Connect the Techstream to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the Techstream and vehicle begins.
  3. Check that there are no electrical key transmitter sub-assemblies in the vehicle.
  4. Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (Click here).
  5. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  6. Before replacing the certification ECU (smart key ECU assembly), refer to the smart key system (for Entry Function) precaution (Click here).
  7. After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
  8. The door control & tire pressure monitoring has a constant voltage (5 V) supply circuit connected to terminal "+5".
  9. When replacing the door control & tire pressure monitoring, read the transmitter IDs (tire pressure warning system) stored in the old ECU using the Techstream and write them down before removal (Click here).
  10. It is necessary to perform initialization (Click here) after registration (Click here) of the transmitter IDs into the door control & tire pressure monitoring if the door control & tire pressure monitoring has been replaced.

1.INSPECT AUXILIARY BATTERY VOLTAGE
  1. Measure the voltage of the vehicle auxiliary battery with the power switch off.

    Standard voltage:
    11 to 14 V

    HINT:
    It may be possible to tell whether the vehicle auxiliary battery is discharged by operating the horn.

    1. If the voltage is below 11 V, recharge or replace the vehicle auxiliary battery before proceeding.


NEXT


2.CHECK FOR DTC
  1. Open the driver door using the mechanical key built into the electrical key transmitter sub-assembly.

  1. Connect the Techstream and check for DTCs (Click here).

    HINT:
    When using the Techstream with the power switch off to troubleshoot: Connect the Techstream to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the Techstream and vehicle begins.

    OK:
    DTC is not output.



NG
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
OK


3.CHECK POWER DOOR LOCK CONTROL SYSTEM
  1. When the door control switch on the multiplex network master switch assembly on the driver door is operated, check that the doors unlock and lock according to the switch operation (Click here).

    OK:
    Door locks operate normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


4.CHECK KEY DIAGNOSTIC MODE
  1. Check the following antennas in the key diagnostic mode (Click here).



  1. Select either channel 1 or channel 2 and inspect the key diagnostic mode for each channel.

    HINT:
    If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter cannot be detected by channel 2 due to a malfunction, such as wave interference.



      B300371E01
    1. Check the electrical key antenna (for driver door):
      Text in Illustration 
      *a
      0.7 to 1 m (2.30 to 3.28 ft.)
      When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless door lock buzzer sounds.



    2. B300370E01
    3. Check the electrical key antenna (for front passenger door):
      Text in Illustration 
      *a
      0.7 to 1 m (2.30 to 3.28 ft.)
      When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for front passenger door), check that the wireless door lock buzzer sounds.



    4. B300374E01
    5. Check the No. 1 indoor electrical key antenna (front floor):
      Text in Illustration 
      *a
      Inspection Point
      When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.



    6. B300406E01
    7. Check the No. 2 indoor electrical key antenna (steering column):
      Text in Illustration 
      *a
      Inspection Point
      When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.



    8. B300375E01
    9. Check the No. 3 indoor electrical key antenna (rear floor):
      Text in Illustration 
      *a
      Inspection Point
      When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.



    10. B300384E01
    11. Check the electrical key antenna (outside luggage):
      Text in Illustration 
      *a
      0.7 to 1 m (2.30 to 3.28 ft.)
      When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage), check that the wireless door lock buzzer sounds.

      OK:
      Wireless door lock buzzer sounds.

      Result:
      Result
      Proceed to
      Diagnostic mode inspections fail for both channels
      A
      Diagnostic mode inspections succeed for both channels
      B
      Diagnostic mode inspection succeeds for only one of the channels
      C



B
Go to step 10

C
Go to step 21
A


5.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
  1. Check if there are any other registered electrical key transmitter sub-assemblies.

Result:
Result
Proceed to
There are no other registered electrical key transmitter sub-assemblies
A
There is another registered electrical key transmitter sub-assemblies
B



B
Go to step 7
A


6.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
  1. Register a new electrical key transmitter sub-assembly (Click here).


NEXT


7.CHECK ENTRY DOOR LOCK OPERATION
  1. Using another or newly registered electrical key transmitter sub-assembly, check if an entry lock/unlock operation can be performed twice in succession.

    OK:
    Entry lock/unlock operate normally twice.



NG
Go to step 10
OK


8.CHECK TRANSMITTER BATTERY
  1. Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.

    1. Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.

      Result:
      Result
      Proceed to
      Transmitter LED does not illuminate when switch is pressed and held
      A
      Transmitter LED illuminates 3 times or more when switch is pressed and held
      B
      Transmitter LED illuminates once or twice but not a third time
      C

      HINT:
      1. The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less (Click here).
      2. Even if the transmitter battery is depleted, it is still possible to start the hybrid system by holding the electrical key transmitter sub-assembly against the power switch, depressing the brake pedal and pressing the power switch.



B
REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY (Click here)

C
REPLACE TRANSMITTER BATTERY (Click here)
A


9.INSPECT TRANSMITTER BATTERY (VOLTAGE)


  1. Inspect the transmitter battery



      B281811E01
    1. Remove the transmitter battery from the electrical key transmitter sub-assembly that does not operate (Click here).

    2. Attach a lead wire (0.60 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal.
      Text in Illustration 
      *1
      Lead Wire

      NOTICE:
      Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.

    3. Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.



    4. B281812E01
    5. Measure the voltage of the transmitter battery.

      HINT:
      1. When measuring the transmitter battery voltage, bring the electrical key transmitter sub-assembly within the lock entry operating range while operating the lock sensor of a door handle to perform the measurement.
      2. Perform the measurement when the key is at room temperature.
      3. The key sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. When this voltage is 2.2 V or less the Data List item "Key Low Battery" displays "Yes". (Click here)

      Text in Illustration 
      *1
      GND

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      Transmitter battery positive (+) - Transmitter battery negative (-)
      Power switch off, all doors closed and lock sensor touched
      2.3 to 3.2 V



NG
REPLACE TRANSMITTER BATTERY (Click here)
OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY (Click here)  

10.CHECK WAVE ENVIRONMENT
  1. Bring the electrical key transmitter sub-assembly near the door control & tire pressure monitoring and perform a wireless and entry function operation check.

    HINT:
    1. When the electrical key transmitter sub-assembly is brought near the door control & tire pressure monitoring, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
    2. If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
    3. There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
    4. If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.

    OK:
    Wireless and entry functions operate normally.



NG
Go to step 11
OK

AFFECTED BY WAVE INTERFERENCE 

11.CHECK POWER MANAGEMENT CONTROL ECU


  1. Measure the voltage according to the value(s) in the table below.


    B290528E03


    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)
    -
    -

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Power Source Control / Data List.

  1. Read the Data List according to the display on the Techstream.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Power Supply Condition
    Power supply state/IG2 ON, ST ON, All OFF, IG1 ON or ACC ON
    ALL OFF: Power switch off (ACC and IG)
    ACC ON: Power switch on (ACC) (ACC relay on)
    IG1 ON: Power switch on (IG) (IG1 relay on)
    IG2 ON: Power switch on (IG) (IG2 relay on)
    ST ON: Sending hybrid system start request signal
    Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time).

  1. Measure the voltage while checking the Data List on the Techstream.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G58-2 (IG1D) - Body ground
    Power switch off
    Below 1 V
    Power switch on (ACC)
    Below 1 V
    Power switch on (IG)
    8 to 14 V
    A39-2 (IG2D) - Body ground
    Power switch off
    Below 1 V
    Power switch on (ACC)
    Below 1 V
    Power switch on (IG)
    8 to 14 V
    G58-1 (ACCD) - Body ground
    Power switch off
    Below 1 V
    Power switch on (IG)
    8 to 14 V
    Power switch on (ACC)
    8 to 14 V

    HINT:
    Using the Techstream, measure the voltage while confirming the power source mode on the Data List.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (Click here)
OK


12.READ VALUE USING TECHSTREAM (IG SW)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Smart Key / Data List.

  1. Read the Data List according to the display on the Techstream.

    Smart Key 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Ignition Switch
    Power switch on (IG) / ON or OFF
    ON: Power switch on (IG)
    OFF: Power switch off
    1. Displays whether the IG power source signal input is on or off.
    2. Use this Data List item to help determine the cause when all smart key system/wireless functions do not operate.
    3. If the electrical key transmitter sub-assembly is brought inside the vehicle and the power switch is pressed twice without depressing the brake pedal, the power switch will turn on (IG). At this time, the key ID code transmitted from the electrical key transmitter sub-assembly and the key ID code stored in the ID code box (immobiliser code ECU) are compared, and the S code stored in the ID code box (immobiliser code ECU) and the code stored in the steering lock ECU (steering lock actuator assembly) are compared, and if all codes match, the power source mode is considered on (IG) at that time.



NG
CHECK RELAY CONTACT SIDE CIRCUIT
OK


13.READ VALUE USING TECHSTREAM (ACC SW, IG SW)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. Read the Data List according to the display on the Techstream.


Main Body 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
ACC SW
Power switch status / ON or OFF
ON: Power switch on (ACC)
OFF: Power switch off
-
IG SW
Power switch status / ON or OFF
ON: Power switch to on (IG)
OFF: Power switch off
-

HINT:
If the certification ECU (smart key ECU assembly) misjudges that the power source is on even though the power source is off for any reason, the entry lock/unlock functions stop.

OK:
The main body ECU (multiplex network body ECU) judges properly that the power source is off when the power source is off.



NG
TROUBLESHOOT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK


14.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - AUXILIARY BATTERY AND BODY GROUND)


  1. Disconnect the G54 and G55 certification ECU (smart key ECU assembly) connectors.


    B288569E03

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    G55-1 (E) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:

    Tester Connection
    Condition
    Specified Condition
    G54-4 (CUTB) - Body ground
    Power switch off
    11 to 14 V
    G54-5 (+B) - Body ground
    Power switch off
    11 to 14 V


Text in Illustration 
*a
Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))
-
-


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR CONTROL & TIRE PRESSURE MONITORING)
  1. Disconnect the G53 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the M17 door control & tire pressure monitoring connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    G53-15 (RCO) - M17-10 (+5)
    Always
    Below 1 Ω
    G53-6 (RDAM) - M17-9 (DATA)
    Always
    Below 1 Ω
    G53-7 (CSEL) - M17-6 (CSEL)
    Always
    Below 1 Ω
    G53-15 (RCO) or M17-10 (+5) - Body ground
    Always
    10 kΩ or higher
    G53-6 (RDAM) or M17-9 (DATA) - Body ground
    Always
    10 kΩ or higher
    G53-7 (CSEL) or M17-6 (CSEL) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


16.CHECK DOOR CONTROL & TIRE PRESSURE MONITORING (GND)


    B274835E33
  1. Connect the M17 door control & tire pressure monitoring connector.

  1. Connect the G53 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    M17-12 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Door Control & Tire Pressure Monitoring)



NG
REPLACE DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY (Click here)
OK


17.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Connect the G53 certification ECU (smart key ECU assembly) connector.

  1. Connect the M17 door control & tire pressure monitoring connector.



    B274835E41
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:

    Tester Connection
    Condition
    Specified Condition
    M17-10 (+5) - M17-12 (GND)
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly switch not pressed
    Below 1 V
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly switch pressed
    4.5 to 5.5 V
    M17-6 (CSEL) - M17-12 (GND)
    Power switch off and all doors closed
    Below 1 V → 4.4 to 6.5 V → Below 1 V
    M17-1 (IG) - M17-12 (GND)
    Power switch on (IG)
    10 to 16 V
    M17-7 (+B) - M17-12 (GND)
    Always
    10 to 16 V

    Text in Illustration 
    *a
    Component with harness connected
    (Door Control & Tire Pressure Monitoring)



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (Click here)
OK


18.CHECK DOOR CONTROL & TIRE PRESSURE MONITORING
  1. Connect the G53 certification ECU (smart key ECU assembly) connector.

  1. Connect the M17 door control & tire pressure monitoring connector.



    B274835E35
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:

    Tester Connection
    Condition
    Specified Condition
    M17-9 (DATA) - M17-12 (GND)
    Procedure:
    1. All doors closed
    2. All doors locked
    3. Electrical key transmitter sub-assembly switch pressed
    Below 2 V → 10 to 16 V → Below 2 V
    M17-6 (CSEL) - M17-12 (GND)
    Procedure:
    1. Power switch off
    2. All doors closed
    11 to 14 V → Below 2 V

    Text in Illustration 
    *a
    Component with harness connected
    (Door Control & Tire Pressure Monitoring)



NG
REPLACE DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY (Click here)
OK


19.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Temporarily replace the certification ECU (smart key ECU assembly) with a new one.

    HINT:
    1. For replacement, (Click here).
    2. For registration, (Click here).


NEXT


20.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
  1. Check that the wireless door lock functions operate normally (Click here).

    OK:
    Wireless door lock functions operate normally.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE) 

21.CHECK WAVE ENVIRONMENT
  1. Bring the electrical key transmitter sub-assembly that was checked first near the door control & tire pressure monitoring and select the failed channel (the channel in which the buzzer did not sound) to recheck the key diagnostic mode (Click here).

    HINT:
    1. When the electrical key transmitter sub-assembly is brought near the door control & tire pressure monitoring, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
    2. If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
    3. There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
    4. If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.

    OK:
    Wireless door lock buzzer sounds.



NG
Go to step 22
OK

AFFECTED BY WAVE INTERFERENCE 

22.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
  1. Check if there are any other registered electrical key transmitter sub-assemblies.

Result:
Result
Proceed to
There are no other registered electrical key transmitter sub-assemblies
A
There is another registered electrical key transmitter sub-assemblies
B



B
Go to step 24
A


23.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
  1. Register a new electrical key transmitter sub-assembly (Click here).


NEXT


24.CHECK WAVE ENVIRONMENT
  1. Bring another or newly registered electrical key transmitter sub-assembly near the door control & tire pressure monitoring and select the failed channel (the channel in which the buzzer did not sound) to recheck the key diagnostic mode (Click here).

HINT:
  1. When the electrical key transmitter sub-assembly is brought near the door control & tire pressure monitoring, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
  2. If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
  3. There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
  4. If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.

OK:
Wireless door lock buzzer sounds.



NG
Go to step 25
OK

END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY THAT WAS INSPECTED FIRST WAS DEFECTIVE) 

25.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR CONTROL & TIRE PRESSURE MONITORING)
  1. Disconnect the G53 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the M17 door control & tire pressure monitoring connector.

  1. Measure the resistance according to the value(s) in the table below.


Standard Resistance:

Tester Connection
Condition
Specified Condition
G53-7 (CSEL) - M17-6 (CSEL)
Always
Below 1 Ω
G53-7 (CSEL) or M17-6 (CSEL) - Body ground
Always
10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


26.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
B274835E36
  1. Connect the G53 certification ECU (smart key ECU assembly) connector.

  1. Connect the M17 door control & tire pressure monitoring connector.

  1. Measure the voltage according to the value(s) in the table below.


Standard Voltage:

Tester Connection
Condition
Specified Condition
M17-6 (CSEL) - M17-12 (GND)
Power switch off and all doors closed
Below 1 V → 4.5 to 6 V → Below 1 V

Text in Illustration 
*a
Component with harness connected
(Door Control & Tire Pressure Monitoring)


NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (Click here)
OK


27.CHECK DOOR CONTROL & TIRE PRESSURE MONITORING
  1. Connect the G53 certification ECU (smart key ECU assembly) connector.

  1. Connect the M17 door control & tire pressure monitoring connector.



    B274835E37
  1. Measure the voltage according to the value(s) in the table below.

    HINT:
    Inspection should be performed while the electrical key antenna check in key diagnostic mode is being performed on the failed channel (the channel in which the buzzer did not sound).


    Standard Voltage:

    Tester Connection
    Condition
    Specified Condition
    M17-9 (DATA) - M17-12 (GND)
    Procedure:
    1. All doors closed
    2. All doors locked
    3. Electrical key transmitter sub-assembly switch pressed*
    Below 1 V → 10 to 16 V → Below 1 V

    1. *: While the electrical key antennas are being inspected in key diagnostic mode (Click here).
    Text in Illustration 
    *a
    Component with harness connected
    (Door Control & Tire Pressure Monitoring)



NG
REPLACE DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY (Click here)
OK


28.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Temporarily replace the certification ECU (smart key ECU assembly) with a new one.

    HINT:
    1. For replacement (Click here).
    2. For registration (Click here).


NEXT


29.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
  1. Check that the wireless door lock functions operate normally (Click here).

    OK:
    Wireless door lock functions operate normally.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)