Home › Engine / Hybrid System › 1NZ-FXE ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > ECM Power Source Circuit

for Preparation Click here


DESCRIPTION

When the ignition switch is turned to ON (IG), auxiliary battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes current to flow to the coil of the No. 1 integration relay (EFI MAIN relay), closing the contact and supplying power to terminals +B and +B2 of the ECM.

WIRING DIAGRAM


A275614E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    C10-16 (E1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK TERMINAL VOLTAGE (IGSW VOLTAGE)


    A255690E16
  1. Disconnect the ECM connector.

  1. Turn the ignition switch to ON (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A40-37 (IGSW) - Body ground
    Ignition switch ON (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
Go to step 6
OK


3.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN RELAY)
  1. Inspect the No. 1 integration relay (EFI MAIN relay) (Click here).



NG
REPLACE NO. 1 INTEGRATION RELAY (EFI MAIN RELAY) (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
  1. Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    2C-4 - A40-2 (+B)
    Always
    Below 1 Ω
    2C-4 - A40-3 (+B2)
    Always
    Below 1 Ω
    2C-3 - A40-46 (MREL)
    Always
    Below 1 Ω
    2C-4 or A40-2 (+B) - Body ground
    Always
    10 kΩ or higher
    2C-4 or A40-3 (+B2) - Body ground
    Always
    10 kΩ or higher
    2C-3 or A40-46 (MREL) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)


    A260483E02
  1. Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    2E-1 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 1 Integration Relay)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - NO. 1 INTEGRATION RELAY)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

6.INSPECT NO. 1 INTEGRATION RELAY (IG2 RELAY)
  1. Inspect the No. 1 integration relay (IG2 relay) (Click here).



NG
REPLACE NO. 1 INTEGRATION RELAY (IG2 RELAY) (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
  1. Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    2D-4 - A40-37 (IGSW)
    Always
    Below 1 Ω
    2D-4 or A40-37 (IGSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)


    A260483E02
  1. Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    2E-1 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 1 Integration Relay)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - NO. 1 INTEGRATION RELAY)
OK


9.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)
  1. Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    2D-2 - Body ground
    Always
    Below 1 Ω


    Result 
    Result
    Proceed to
    OK (w/ Smart key system)
    A
    OK (w/o Smart key system)
    B
    NG
    C



B
Go to step 11

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


10.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 1 INTEGRATION RELAY)
  1. Disconnect the power management control ECU connector.

  1. Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A39-2 (IG2D) - 2D-3
    Always
    Below 1 Ω
    A39-2 (IG2D) or 2D-3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO SMART KEY SYSTEM (Click here)  

11.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - NO. 1 INTEGRATION RELAY)
  1. Disconnect the ignition or starter switch assembly connector.

  1. Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    G15-6 (IG2) - 2D-3
    Always
    Below 1 Ω
    G15-6 (IG2) or 2D-3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
  1. Inspect the ignition or starter switch assembly (Click here).



NG
REPLACE IGNITION OR STARTER SWITCH ASSEMBLY (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - AUXILIARY BATTERY)