Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0AC0-817    Hybrid Battery Pack Current Sensor Circuit Range / Performance

for Preparation Click here


DESCRIPTION


  1. The battery current sensor, which is located in the hybrid battery junction block assembly on the positive side of the HV battery, detects the amperage that flows to and from the HV battery. The battery smart unit receives a voltage of between 0 and 5 V that is in proportion to the amperage flowing in the cable. This voltage goes into the IB terminal from the battery current sensor. A battery current sensor output voltage below 2.5 V indicates that the HV battery is being charged, and a voltage above 2.5 V indicates that the HV battery is being discharged. The power management control ECU determines the amount of either charge or discharge amperage that is being received by the HV battery based on the signals that are input to terminal IB of the battery smart unit from the battery current sensor. The power management control ECU also calculates the SOC (state of charge) of the HV battery based on the accumulated amperage.


    A304993E01


DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0AC0
817
Abnormal battery current sensor characteristics
An abnormality in the battery current sensor characteristics is detected based on the relationship between hybrid system power consumption and battery power output.
(1 trip detection logic)
  1. Hybrid battery junction block assembly
  2. Battery smart unit

Related Data List 
DTC No.
Data List
P0AC0-817
Power Resource IB

MONITOR DESCRIPTION

The power management control ECU detects malfunctions of the battery current sensor by monitoring MG1 and MG2 torque. If the power management control ECU detects a battery current sensor malfunction, the power management control ECU will illuminate the MIL and set a DTC.

MONITOR STRATEGY


Related DTCs
P0AC0 (INF 817): Current sensor malfunction (gain or offset)
Required sensors / components
Battery current sensor
Frequency of operation
Continuous
Duration
TMC's intellectual property
MIL operation
TMC's intellectual property
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TMC's intellectual property
Other conditions belong to TMC's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


TMC's intellectual property
-

COMPONENT OPERATING RANGE


Power management control ECU
DTC P0AC0 (INF 817) is not detected

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for 30 seconds or more.
  5. Turn the ignition switch to ON (IG) and turn the Techstream on.
  6. Turn the ignition switch to ON (READY).
  7. Drive the vehicle for approximately 10 minutes according to the freeze frame data items "Vehicle Spd", "Accelerator Degree", "Power Resource IB", "M(MG2) Trq Exec Val" and "G(MG1) Trq Exec Val".
  8. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
  9. Read the current DTCs.

    HINT:
    1. If a current DTC is output, the system is malfunctioning.
    2. If a current DTC is not output and want to confirm permanent DTC, perform the following procedure.

  10. Check that permanent DTCs are cleared. If no permanent DTC is output, the system is normal.
  11. If the permanent DTCs are not cleared, perform a universal trip, and check for permanent DTCs again.

INSPECTION PROCEDURE

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Drive the vehicle for approximately 10 minutes according to the freeze frame data items "Vehicle Spd", "Accelerator Degree", "Power Resource IB", "M(MG2) Trq Exec Val" and "G(MG1) Trq Exec Val".

1.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P0AC0-817 only is output.
    A
    P0AFC-123 is output.
    B

  1. Turn the ignition switch off.



B
GO TO DTC CHART (P0AFC-123) (Click here)
A


2.REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY
(Click here)

NEXT


3.CLEAR DTC
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Read and record the DTCs and freeze frame data.

  1. Clear DTCs and freeze frame data.

  1. Turn the ignition switch off.


NEXT


4.PERFORM ROAD TEST
  1. Perform a "Confirmation Driving Pattern".


NEXT


5.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P0AC0-817 is not output.
    A
    P0AC0-817 is output again.
    B

  1. Turn the ignition switch off.



B
REPLACE BATTERY SMART UNIT (Click here)
A

COMPLETED