Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT DOOR BELT MOULDING

FRONT DOOR BELT MOULDING > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure described below is for the LH side.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).



2. REMOVE FRONT FLOOR COVER RH


    B301488E01
  1. Using a clip remover, remove the 2 clips <A>.

  1. Disengage the 3 clips <B>.



    B301489
  1. Disengage the 3 guides and remove the front floor cover RH.



3. DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



4. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER
(Click here)


5. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY


    E237142
  1. Disconnect the connector.

  1. Remove the 2 screws and front No. 2 speaker assembly.



6. REMOVE DOOR SIDE AIRBAG SENSOR
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



    B300237
  1. Disconnect the connector from the door side airbag sensor.

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.




    1. Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)


      H043302E12


      Text in Illustration 
      *1
      White Housing Lock
      *2
      Yellow CPA
      *a
      Connector Lock is Released
      -
      -

    2. Push down the white housing lock again and disconnect the connector.

      NOTICE:
      Do not push down the part (A) shown in the illustration when disconnecting.



    B300238
  1. Remove the bolt and door side airbag sensor from the front door panel.

    NOTICE:
    Loosen the bolt while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.



  1. After disconnecting the connector, check that the position of the white housing lock is correct as shown in the illustration.


    B296255E01


    Text in Illustration 
    *a
    Incorrect
    *b
    Correct



7. REMOVE FRONT DOOR SERVICE HOLE COVER


    B310970
  1. Remove the bolt and disconnect the earth wire.

    NOTICE:
    Remove any remaining butyl tape from the front door panel.

  1. Remove the front door service hole cover.



8. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    B307087
  1. Remove the front door No. 2 service hole cover.

  1. Connect the cable to the negative (-) auxiliary battery terminal and power window regulator master switch assembly and move the front door glass subassembly so that the door glass bolts can be seen.

  1. Disconnect the negative (-) auxiliary battery terminal and power window regulator master switch assembly.



    B307088
  1. Remove the 2 bolts.

    NOTICE:
    After the bolts are removed, do not allow the door glass to fall.



    B307089
  1. Remove the front door glass sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.



9. REMOVE FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY


    B298004E01
  1. Apply protective tape to the door panel in the area around the front door glass outer weatherstrip assembly.
    Text in Illustration 
    *1
    Protective Tape



    B297999E01
  1. Using a screwdriver with the tip wrapped with protective tape, disengage the 5 claws.
    Text in Illustration 
    *1
    Protective Tape

  1. Disengage the guide and remove the front door glass outer weatherstrip assembly.