DTC P0401 Exhaust Gas Recirculation Flow Insufficient Detected |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0401 | Change in intake manifold pressure is small when the EGR valve is opened and closed during idle fuel cut operation (2 trip detection logic). |
|
| Related DTCs | P0401: EGR valve high flow rate/low flow rate |
| Required Sensors/Components (Main) | EGR valve assembly Manifold absolute pressure sensor |
| Required Sensors/Components (Related) | Engine coolant temperature sensor Vehicle speed sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | Within 3 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever the following DTCs are not stored | None |
| Time after engine started | 3 seconds or more |
| Time after engine fuel cut | 1300 msec or more |
| Engine speed | 950 to 1600 rpm |
| Vehicle speed | 20 km/h (12.5 mph) or more |
| Engine coolant temperature | 75°C (167°F) or higher |
| Auxiliary battery voltage | 11 V or higher |
| Intake air temperature | -10°C (14°F) or higher |
| Atmospheric pressure | 76 kPa(abs) [570 mmHg(abs)] or higher |
| Manifold pressure change | Less than 1.75 kPa [13.1 mmHg] |
| At engine speed | 1050 rpm |
| Monitor ID | Test ID | Scaling | Unit | Description |
| $31 | $BD | Multiply by 0.01 | kPa | Delta Manifold Absolute Pressure |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| Data List | Change in Data List when Number of Steps is Increased Using Control the EGR Step Position Active Test |
| Engine Speed | Idle becomes rough |
| MAP | Pressure rises |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0401) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTC.
| Result | Proceed to |
| DTC P0401 is output | A |
| DTC P0401 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Turn the Techstream on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Primary / Throttle Idle Position and MAP.
Confirm that the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| Idling condition (Throttle Idle Position: ON) | Steady idling | Idling changes from steady to rough idling or engine stalls |
| MAP (Data List) | MAP value is 20 to 40 kPa(abs) [150 to 300 mmHg(abs)] (EGR valve is fully closed) | MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
|
| ||||
| OK | |
| 3.INSPECT EGR VALVE ASSEMBLY |
Check if the EGR valve are clogged with deposits.
Check if the EGR valve is closed.
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 4.REPLACE EGR VALVE ASSEMBLY |
Replace the EGR valve assembly (Click here).
| NEXT | |
| 5.CHECK FOR DEPOSIT (INTAKE PORT AND EXHAUST MANIFOLD SUB-ASSEMBLY TO EGR VALVE ASSEMBLY) |

Check for exhaust leaks at each connection point.
Check for cracks, damage, and clogs in the pipes between the intake manifold, the EGR valve assembly and the exhaust manifold sub-assembly.
This check may require the removal of components.
Check if there is a build-up of deposits in the EGR valve of pipes.
|
| ||||
| OK | |
| 6.INSPECT EGR COOLER ASSEMBLY |
Check for blockage of the EGR cooler assembly.
|
| ||||
| OK | |
| 7.READ VALUE USING TECHSTREAM (MAP) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / MAP.
Read the MAP value.
| Condition | Techstream Display |
| Ignition switch ON (IG) | 80 to 110 kPa(abs) [600 to 825 mmHg(abs)] |
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / MAP.
Read the MAP value when idling the engine with the A/C switch and all accessory switches should be off and shift lever in P or N.
| Engine Condition | Techstream Display |
| Idling | Less than 80 kPa(abs) [600 mmHg(abs)] |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 8.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks (Click here).
|
| ||||
| OK | |
| 9.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR |
Replace the manifold absolute pressure sensor (Click here).
| NEXT | |
| 10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON (IG).
Turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read the pending DTCs.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0401.
Check the DTC judgment result.
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| NEXT | ||
| ||