Home › Engine / Hybrid System › 1NZ-FXE ENGINE CONTROL › SFI SYSTEM

DTC    P261B    Engine Coolant Pump "B" Control Malfunction

DTC    P261C    Engine Coolant Pump "B" Control Circuit Low

DTC    P261D    Engine Coolant Pump "B" Control Circuit High

for Preparation Click here


DESCRIPTION

The ECM controls the engine water pump assembly by calculating the necessary amount of coolant flow based on engine coolant temperature, engine speed and vehicle speed information. The speed of the engine water pump assembly is controlled steplessly using a duty cycle signal sent from the ECM. This optimal control enhances warm-up performance and reduces cooling losses, thus reducing the specific fuel consumption of the engine.

DTC No.
DTC Detection Condition
Trouble Area
P261B
Engine water pump assembly speed is less than 900 rpm while the engine water pump assembly is operating (1 trip detection logic).
  1. Open or short in engine water pump assembly circuit
  2. Engine water pump assembly
  3. ECM
P261C
Engine water pump assembly output voltage is less than specified value while the engine water pump assembly is operating (1 trip detection logic).
  1. Short in engine water pump assembly circuit
  2. Engine water pump assembly
  3. ECM
P261D
Engine water pump assembly output voltage is higher than specified value while the engine water pump assembly is operating (1 trip detection logic).
  1. Open in engine water pump assembly circuit
  2. Engine water pump assembly
  3. ECM

MONITOR DESCRIPTION

The ECM calculates the speed of the engine water pump assembly using a duty cycle signal sent from the engine water pump assembly. When the speed of the engine water pump assembly becomes less than 900 rpm while it is operating, the ECM detects the malfunction and stores DTC P261B.
The engine water pump assembly operates steplessly based on a duty cycle signal sent from the ECM. If actual drive duty cycle ratio does not correspond to the target drive duty cycle of the engine water pump assembly, the ECM detects the malfunction.

MONITOR STRATEGY


Related DTCs
P261B: Engine water pump circuit performance
P261C: Engine water pump circuit range check (low voltage)
P261D: Engine water pump circuit range check (high voltage)
Required Sensors/Components (Main)
Engine water pump assembly
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
15 seconds: Engine water pump circuit performance
3 seconds: Engine water pump circuit range check (low voltage, high voltage)
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever the following DTCs are not stored
None
All of the following conditions are met
-
Auxiliary battery voltage
8 V or higher
Ignition switch
ON (IG)
Time after ignition switch off to ON (IG)
More than 0.5 seconds

P261B 
All of the following conditions are met
-
Output duty cycle
30% or more
Monitor synchronism monitor status
Enable
Engine coolant temperature
-10°C (14 °F) or higher
Engine coolant temperature sensor circuit fail (P0115, P0117, P0118)
Not detected
Engine water pump circuit low voltage fail (P261C)
Not detected
Engine water pump circuit high voltage fail (P261D)
Not detected

P261C and P261D 
Both of the following conditions are met
-
Output duty cycle
30 to 85%
Engine water pump circuit performance fail (P261B)
Not detected

TYPICAL MALFUNCTION THRESHOLDS


P261B 
Motor speed
Less than 900 rpm

P261C 
Both of the following conditions are met
-
Engine water pump output terminal voltage level
Low
Engine water pump output signal
No signal

P261D 
Both of the following conditions are met
-
Engine water pump output terminal voltage level
High
Engine water pump output signal
No signal

COMPONENT OPERATING RANGE


P261B 
Motor speed
900 rpm or more

P261C and P261D 
Engine water pump output signal
Signal input

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON (IG) and turn the Techstream on.
  6. Put the engine in inspection mode (maintenance mode) (Click here).
  7. Start the engine and warm it up (until the engine coolant temperature is 75°C (167°F) or higher).
  8. Idle the engine for 20 seconds or more [A].
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  10. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P261B, P261C or P261D.
  13. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.

  14. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A275613E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.PERFORM ACTIVE TEST USING TECHSTREAM (ACTIVATE THE ELECTRIC WATER PUMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Electric Water Pump.

  1. Touch the engine water pump and check that the pump assembly is operating (vibrating).

    OK:
    The engine water pump assembly is operating (vibrating).



NG
Go to step 4
OK


2.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY - ECM)

HINT:
Confirm a good connection at the engine water pump assembly and ECM connectors.

  1. Disconnect the engine water pump assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    C27-2 (NWP) - A40-28 (WPI)
    Always
    Below 1 Ω
    C27-4 (SWP) - A40-29 (WPO)
    Always
    Below 1 Ω
    C27-2 (NWP) or A40-28 (WPI) - Body ground
    Always
    10 kΩ or higher
    C27-4 (SWP) or A40-29 (WPO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK TERMINAL VOLTAGE (WPI VOLTAGE)


    A215890E16
  1. Disconnect the engine water pump assembly connector.

  1. Turn the ignition switch to ON (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    C27-2 (NWP) - Body ground
    Ignition switch ON (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Engine Water Pump Assembly)



NG
REPLACE ECM (Click here)
OK

REPLACE ENGINE WATER PUMP ASSEMBLY (Click here)  

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ENGINE WATER PUMP ASSEMBLY)

HINT:
Confirm a good connection at the engine water pump assembly and ECM connectors.



    A215890E17
  1. Disconnect the engine water pump assembly connector.

  1. Turn the ignition switch to ON (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    C27-1 (+B) - Body ground
    Ignition switch ON (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Engine Water Pump Assembly)



NG
Go to step 9
OK


5.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY - BODY GROUND)
  1. Disconnect the engine water pump assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    C27-5 (PGND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY - ECM)
  1. Disconnect the engine water pump assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    C27-2 (NWP) - A40-28 (WPI)
    Always
    Below 1 Ω
    C27-4 (SWP) - A40-29 (WPO)
    Always
    Below 1 Ω
    C27-2 (NWP) or A40-28 (WPI) - Body ground
    Always
    10 kΩ or higher
    C27-4 (SWP) or A40-29 (WPO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.REPLACE ENGINE WATER PUMP ASSEMBLY
  1. Replace the engine water pump assembly (Click here).


NEXT


8.CHECK WHETHER DTC OUTPUT RECURS (DTC P261B, P261C OR P261D)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON (IG).

  1. Turn the Techstream on.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P261B, P261C or P261D is output
    A
    DTC is not output
    B



B
END
A

REPLACE ECM (Click here)  

9.INSPECT RELAY (ENG W/PMP RELAY)


    A234567E01
  1. Remove the ENG W/PMP relay from the No. 2 engine room relay block and No. 2 junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    No auxiliary battery voltage applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Auxiliary battery voltage applied between terminals 1 and 2
    Below 1 Ω



NG
REPLACE RELAY (ENG W/PMP RELAY)
OK


10.CHECK HARNESS AND CONNECTOR (ENG W/PMP RELAY - ENGINE WATER PUMP ASSEMBLY)
  1. Remove the ENG W/PMP relay from the No. 2 engine room relay block and No. 2 junction block assembly.

  1. Disconnect the engine water pump assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    ENG W/PMP relay terminal 3 - C27-1 (+B)
    Always
    Below 1 Ω
    ENG W/PMP relay terminal 3 or C27-1 (+B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ENG W/PMP RELAY)


    A268185E01
  1. Remove the ENG W/PMP relay from the No. 2 engine room relay block and No. 2 junction block assembly.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    ENG W/PMP relay terminal 5 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
    *2
    ENG W/PMP Relay



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - ENG W/PMP RELAY)
OK


12.CHECK HARNESS AND CONNECTOR (ENG W/PMP RELAY - BODY GROUND)
  1. Remove the ENG W/PMP relay from the No. 2 engine room relay block and No. 2 junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    ENG W/PMP relay terminal 1 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENG W/PMP RELAY - EFI MAIN RELAY)