Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Smart Key System)

DTC    B2779    Engine Starter Communication Malfunction

for Preparation Click here


DESCRIPTION

If communication between the remote engine starter ECU and certification ECU (smart key ECU assembly) cannot be performed even if a remote engine start operation is performed to try changing the power source mode to on (IG) or start the hybrid control system, this DTC is stored.
When the remote engine starter ECU does not respond to the certification ECU (smart key ECU assembly), this DTC is stored. When communication with the remote engine starter ECU is established and a remote engine start operation is performed, this DTC is cleared.

DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2779
One of the following conditions is met (1 trip detection logic*):
  1. A remote engine start communication error occurs.
  2. Response is not possible.
  3. Registration has not been performed.
  1. Remote engine starter ECU
  2. Wire harness or connector
  3. Main body ECU (multiplex network body ECU)
  4. Certification ECU (smart key ECU assembly)
A remote engine start operation is performed.
  1. *: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Hybrid control system does not start with remote engine start operation
Hybrid control system cannot be started by remote engine start operation only

Related Data List and Active Test 
DTC Code
Data List and Active Test
B2779
  1. Wireless Starter Com ID
  2. Wireless C Code

WIRING DIAGRAM


B278926E03


INSPECTION PROCEDURE

NOTICE:
  1. Before performing the inspection, check that DTC U0142 is not output.
  2. Before replacing the certification ECU (smart key ECU assembly), refer to Registration (Click here).
  3. After performing repair, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.

HINT:
In this repair manual, only the terminal numbers used for inspection between the main body ECU (multiplex network body ECU) and option connector are listed.

1.READ VALUE USING TECHSTREAM
  1. Turn the power switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Smart Key / Data List.

  1. According to the display on the Techstream, read the Data List.

    Smart Key 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Wireless C Code
    Registration status between remote engine starter ECU and certification ECU (smart key ECU assembly)/No Regd or Regd
    No Regd: ID not registered between remote engine starter ECU and certification ECU (smart key ECU assembly)
    Regd: ID registered between remote engine starter ECU and certification ECU (smart key ECU assembly)
    Problems may be caused by the following:
    1. Remote engine starter ECU registration has not been performed.
    2. Malfunctions in the certification ECU (smart key ECU assembly) or remote engine starter ECU.

    OK:
    "Regd" appears on the screen.

    Result 
    Result
    Proceed to
    "No Regd" appears on the screen
    A
    "Regd" appears on the screen
    B



B
Go to step 4
A


2.REGISTER REMOTE ENGINE START ID
  1. Register the remote engine start ID.


NEXT


3.CHECK REMOTE ENGINE START
  1. Check that the hybrid control system can be started using remote engine start operation.

    OK:
    Hybrid control system can be started using remote engine start operation.



NG
Go to step 4
OK

END (REMOTE ENGINE START ID WAS NOT REGISTERED CORRECTLY) 

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - OPTION CONNECTOR)

HINT:
In this repair manual, only the terminal numbers used for inspection between the main body ECU (multiplex network body ECU) and option connector are listed.

  1. Disconnect the G59 main body ECU (multiplex network body ECU) connector.

  1. Disconnect the G70 option connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G59-25 (BTX) - G70-1 (BTX)
    Always
    Below 1 Ω
    G59-26 (BRX) - G70-2 (BRX)
    Always
    Below 1 Ω
    G59-25 (BTX) - Body ground
    Always
    10 kΩ or higher
    G59-26 (BRX) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE REMOTE ENGINE STARTER ECU
  1. Temporarily replace the remote engine starter ECU with a new one.

  1. Register the remote engine start ID.

  1. Check that the hybrid control system can be started using remote engine start operation.

    OK:
    Hybrid control system can be started using remote engine start operation.



NG
Go to step 6
OK

END (REMOTE ENGINE STARTER ECU WAS DEFECTIVE) 

6.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
  1. Temporarily replace the main body ECU (multiplex network body ECU) with a new or known good one (Click here).

  1. Check that the hybrid control system can be started using remote engine start operation.

    OK:
    Hybrid control system can be started using remote engine start operation.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (Click here)
OK

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)