Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Daytime Running Light Relay Circuit

for Preparation Click here


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the daytime running lights (low-intensity high beam headlights) via the DIM/DRL relay.

WIRING DIAGRAM


E241394E01


INSPECTION PROCEDURE

1.CHECK OPERATION (HIGH BEAM HEADLIGHTS)
  1. Check the operation of the high beam headlights.

    OK:
    The high beam headlights operate normally.



NG
GO TO PROBLEM SYMPTOMS TABLE (Click here)
OK


2.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Active Test.

  1. Check that the daytime running lights illuminate.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Daytime Running Light
    Daytime running lights
    ON/OFF
    -

    OK:
    The daytime running lights illuminate.



NG
Go to step 3
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

3.INSPECT DIM/DRL RELAY


    E191082E09
  1. Remove the DIM/DRL relay from the No. 2 engine room relay block and No. 2 junction block assembly.

  1. Connect a positive (+) lead from the auxiliary battery to terminal 6 (+B).

  1. Connect a negative (-) lead from the auxiliary battery to terminals 2 (DRLS) and 3 (E).

  1. Check for pulses according to the value(s) in the table below.

    Standard:
    Tester Connection
    Condition
    Specified Condition
    1 (HLOR) - Auxiliary battery negative terminal
    Always
    Pulse generation
    5 (HLOL) - Auxiliary battery negative terminal
    Always
    Pulse generation

    Text in Illustration 
    *a
    Component without harness connected
    (DIM/DRL Relay)



NG
REPLACE DIM/DRL RELAY
OK


4.CHECK HARNESS AND CONNECTOR (DIM/DRL RELAY - POWER SOURCE AND BODY GROUND)
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Relay terminal 6 (+B) - Body ground
    Ignition switch ON (IG)
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Relay terminal 3 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (DIM/DRL RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the 3C instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Relay terminal 2 (DRLS) - 3C-22
    Always
    Below 1 Ω
    3C-22 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly (Click here).



    E182506E33
  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3C-22 - MB-25 (DRL)
    Always
    Below 1 Ω
    3C-22 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)