Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM (w/ EGR System)

DTC    P0120    Throttle / Pedal Position Sensor / Switch "A" Circuit Malfunction

DTC    P0121    Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem

DTC    P0122    Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input

DTC    P0123    Throttle / Pedal Position Sensor / Switch "A" Circuit High Input

DTC    P0220    Throttle / Pedal Position Sensor / Switch "B" Circuit

DTC    P0222    Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input

DTC    P0223    Throttle / Pedal Position Sensor / Switch "B" Circuit High Input

DTC    P2135    Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation

for Preparation Click here


DESCRIPTION

HINT:
  1. These DTCs relate to the throttle position sensor.

The throttle position sensor is mounted on the throttle body assembly, and detects the opening angle of the throttle valve. This sensor is a non-contact type. It uses Hall-effect elements in order to yield accurate signals even in extreme conditions.
The throttle position sensor has 2 sensor circuits, each of which transmits a signal, VTA1 and VTA2. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 5 V in proportion to the throttle valve opening angle, and are transmitted to the VTA terminals of the ECM.
As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air fuel ratio correction, power enrichment correction and fuel-cut control.

A210557E27


DTC No.
DTC Detection Condition
Trouble Area
P0120
Output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds or more
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body assembly)
  1. ECM
P0121
Difference between VTA1 and VTA2 voltages less than 0.8 V, or more than 1.6 V for 2 seconds
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body assembly)
  2. Throttle position sensor circuit
  3. ECM
P0122
Output voltage of VTA1 0.2 V or less for 2 seconds or more
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body assembly)
  1. Short in VTA1 circuit
  1. Open in VC circuit
  1. ECM
P0123
Output voltage of VTA1 4.54 V or more for 2 seconds or more
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body assembly)
  1. Open in VTA1 circuit
  1. Open in E2 circuit
  1. Short between VC and VTA1 circuits
  1. ECM
P0220
Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds or more
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body assembly)
  1. ECM
P0222
Output voltage of VTA2 1.75 V or less for 2 seconds or more
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body assembly)
  1. Short in VTA2 circuit
  1. Open in VC circuit
  1. ECM
P0223
Output voltage of VTA2 4.8 V or more, and VTA1 between 0.2 V and 2.02 V, for 2 seconds or more
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body assembly)
  1. Open in VTA2 circuit
  1. Open in E2 circuit
  1. Short between VC and VTA2 circuits
  1. ECM
P2135
Either condition (a) or (b) met (1 trip detection logic):
(a) Difference between output voltages of VTA1 and VTA2 0.02 V or less for 0.5 seconds or more
(b) Output voltage of VTA1 is 0.2 V or less, and VTA2 is 1.75 V or less, for 0.4 seconds or more
  1. Short between VTA1 and VTA2 circuits
  1. Throttle position sensor (built into throttle body assembly)
  1. ECM

FAIL-SAFE

When any of these DTCs, as well as other DTCs relating to electronic throttle control system malfunctions, are set, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 5.5° throttle angle by the return spring. The ECM stops the engine and the vehicle can be driven using solely the hybrid system. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the power switch is then turned off.

WIRING DIAGRAM


A220105E01


INSPECTION PROCEDURE

HINT:
  1. DTC P0121 is stored when the voltages output from VTA1 and VTA2 are not consistent with the characteristics of the sensors. Therefore, check the Freeze Frame Data when this DTC is output. Use the following formula to confirm relative fluctuations in voltage.

    Features of sensor output:
    VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V
    VTA1: Throttle Position No. 1
    VTA2: Throttle position No. 2

  2. If DTC P0121 is output, proceed to "CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)".
  3. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)


  1. Disconnect the throttle body assembly connector.


    A194102E24

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    D4-5 (VC) - D28-88 (VCTA)
    Always
    Below 1 Ω
    D4-6 (VTA) - D28-90 (VTA1)
    Always
    Below 1 Ω
    D4-4 (VTA2) - D28-89 (VTA2)
    Always
    Below 1 Ω
    D4-3 (E2) - D28-111 (ETA)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    D4-5 (VC) or D28-88 (VCTA) - Body ground
    Always
    10 kΩ or higher
    D4-6 (VTA) or D28-90 (VTA1) - Body ground
    Always
    10 kΩ or higher
    D4-4 (VTA2) or D28-89 (VTA2) - Body ground
    Always
    10 kΩ or higher


    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Throttle Body Assembly)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the throttle body assembly connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (THROTTLE POSITION SENSOR - ECM)
OK


2.INSPECT ECM (VC VOLTAGE)


    A194103E07
  1. Disconnect the throttle body assembly connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    D4-5 (VC) - D4-3 (E2)
    Power switch on (IG)
    4.5 to 5.5 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Throttle Body Assembly)

  1. Reconnect the throttle body assembly connector.



NG
REPLACE ECM (Click here)
OK


3.REPLACE THROTTLE BODY ASSEMBLY
  1. Replace the throttle body assembly (Click here).


NEXT


4.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Put the engine in inspection mode (Click here).

  1. Start the engine.

  1. With the vehicle stationary, fully depress and release the accelerator pedal.

  1. Idle the engine for 2 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Result
    Proceed to
    DTC P0120, P0121, P0122, P0123, P0220, P0222, P0223 and/or P2135 is output
    A
    DTC is not output
    B



B
END
A

REPLACE ECM (Click here)