Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM (w/ EGR System)

DTC    P0327    Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)

DTC    P0328    Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)

for Preparation Click here


DESCRIPTION

A flat type knock control sensor is used. Flat type knock control sensors (non-resonant type) have a structure that can detect vibrations over a wide band of frequencies: between approximately 6 kHz and 15 kHz.
Knock control sensors are fitted onto the engine block to detect engine knocking.
The knock control sensor contains a piezoelectric element which generates a voltage when it becomes deformed.
The voltage is generated when the engine block vibrates due to knocking. Occurrence of engine knocking can be suppressed by delaying the ignition timing.

DTC No.
DTC Detection Condition
Trouble Area
P0327
Output voltage of knock control sensor less than 0.5 V for 1 second or more
(1 trip detection logic)
  1. Short in knock control sensor circuit
  1. Knock control sensor
  1. ECM
P0328
Output voltage of knock control sensor more than 4.5 V for 1 second or more
(1 trip detection logic)
  1. Open in knock control sensor circuit
  1. Knock control sensor
  1. ECM

HINT:
When either DTC P0327 or P0328 is set, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the power switch is turned off.

Reference: Inspection using an oscilloscope
A194185E01
The correct waveform is as shown.
ECM Terminal Name
Between KNK1 and EKNK
Tester Range
1 V/DIV., 1 ms./DIV.
Condition
Engine speed maintained at 4000 rpm after warming up engine

WIRING DIAGRAM


A220565E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.READ VALUE USING INTELLIGENT TESTER (KNOCK FEEDBACK VALUE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG) and turn the tester on.

  1. Put the engine in inspection mode (Click here).

  1. Start the engine.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Knock Feedback Value.

  1. Read the value while driving the vehicle.

    OK:
    The value changes.

    HINT:
    Malfunction does not occur
    Knock Feedback Value changes
    Malfunctions occur
    Knock Feedback Value does not change
    The knock feedback value change can be confirmed by running the engine with a high load, for example, by activating the air conditioning system and racing the engine.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.INSPECT ECM (KNK1 VOLTAGE)


    A194105E27
  1. Disconnect the knock control sensor connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G1-2 - G1-1
    Power switch on (IG)
    4.5 to 5.5 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Knock Control Sensor)

  1. Reconnect the knock control sensor connector.



NG
Go to step 4
OK


3.INSPECT KNOCK CONTROL SENSOR


    A148716E20
  1. Remove the knock control sensor.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    120 to 280 kΩ

    Text in Illustration 
    *1
    Component without harness connected
    (Knock Control Sensor)
    *2
    Ohmmeter

  1. Reinstall the knock control sensor.



NG
REPLACE KNOCK CONTROL SENSOR (Click here)
OK

REPLACE ECM (Click here)  

4.CHECK HARNESS AND CONNECTOR (ECM - KNOCK CONTROL SENSOR)


  1. Disconnect the knock control sensor connector.


    A194106E22

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    G1-2 - D28-87 (KNK1)
    Always
    Below 1 Ω
    G1-1 - D28-110 (EKNK)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    G1-2 or D28-87 (KNK1) - Body ground
    Always
    10 kΩ or higher
    G1-1 or D28-110 (EKNK) - Body ground
    Always
    10 kΩ or higher


    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Knock Control Sensor)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the knock control sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - KNOCK CONTROL SENSOR)
OK

REPLACE ECM (Click here)