DTC P0335 Crankshaft Position Sensor "A" Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0335 | When either of following conditions are met: (1 trip detection logic)
|
|
![]() |
| ECM Terminal Name | Between NE+ and NE- Between G2+ and G2- |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling with warm engine |

| 1.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (Click here).
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
Start the engine.
Read the values displayed on the tester while the engine is running.
|
| ||||
| OK | ||
| ||
| 2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE) |
![]() |
Disconnect the crankshaft position sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (NE) - 2 (NE-) | Cold | 1630 to 2740 Ω |
| 1 (NE) - 2 (NE-) | Hot | 2065 to 3225 Ω |
| *1 | Component without harness connected (Crankshaft Position Sensor) |
Reconnect the crankshaft position sensor connector.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) |

Disconnect the crankshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D27-1 (NE) - D28-74 (NE+) | Always | Below 1 Ω |
| D27-2 (NE-) - D28-120 (NE-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| D27-1 (NE) or D28-74 (NE+) - Body ground | Always | 10 kΩ or higher |
| D27-2 (NE-) or D28-120 (NE-) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Crankshaft Position Sensor) | *2 | Front view of wire harness connector (to ECM) |
Reconnect the crankshaft position sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR) |
![]() |
Check the crankshaft position sensor installation.
|
| ||||
| OK | |
| 5.INSPECT NO. 1 CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE) |
Check the teeth of the No. 1 crankshaft position sensor plate (Click here).
|
| ||||
| OK | |
| 6.REPLACE CRANKSHAFT POSITION SENSOR |
Replace the crankshaft position sensor (Click here).
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Put the engine in inspection mode (Click here).
Start the engine and wait for 20 seconds.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0335 is output | B |
|
| ||||
| A | ||
| ||