Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY

STEERING COLUMN ASSEMBLY > REMOVAL

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).



1. PRECAUTION

NOTICE:
Be sure to read Precaution thoroughly before servicing (Click here).



2. PRECAUTION (w/ Navigation System for HDD)

NOTICE:
After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.



3. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD


4. REMOVE REAR NO. 2 FLOOR BOARD


    B227787E01
  1. Disengage the 2 guides <A> as shown in the illustration.

  1. Disengage the 3 guides <B> and remove the rear No. 2 floor board.



5. REMOVE REAR DECK FLOOR BOX
  1. Remove the rear deck floor box.



6. REMOVE REAR NO. 3 FLOOR BOARD


    B227791
  1. Disengage the 2 guides and remove the rear No. 3 floor board.



7. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



8. REMOVE STEERING PAD

HINT:
Refer to the instructions for Removal of the steering pad (Click here).



9. REMOVE STEERING WHEEL ASSEMBLY


    C206245E01
  1. Remove the steering wheel assembly set nut.
    Text in Illustration 
    *1
    Matchmark

  1. Put matchmarks on the steering wheel assembly and steering main shaft.

  1. Disconnect the connectors from the spiral cable.



    C206246E01
  1. Using SST, remove the steering wheel assembly.
    Text in Illustration 
    *1
    Turn
    *2
    Hold

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09955-04071)

    NOTICE:
    Apply a small amount of grease to the threads and tip of SST (09953-05020) before use.



10. REMOVE LOWER STEERING COLUMN COVER

NOTICE:
Removing the lower steering column cover in the incorrect order will cause the parts to break.



    C206253
  1. Push the right and left sides of the lower steering column cover to disengage the 4 claws.



    C206254
  1. Insert fingers into the opening of the tilt lever of the lower steering column cover to disengage the 2 claws.

    HINT:
    Spread the claws to disengage them.



  1. Using a screwdriver, insert the tip into each service hole to disengage the 2 claws to remove the lower steering column cover as shown in the illustration.


    C206255E01


    Text in Illustration 
    *1
    Service Hole
    *2
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



11. REMOVE UPPER STEERING COLUMN COVER


    C206258
  1. Disengage the 2 claws and 2 pins to remove the upper steering column cover.



12. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
  1. Disconnect the connectors from the turn signal switch assembly with spiral cable sub-assembly.



    C206260E01
  1. Using pliers, expand the clamp.
    Text in Illustration 
    *1
    Clamp
    *2
    Claw

  1. While holding the clamp expanded, raise the claw using a screwdriver to disengage it, and then remove the turn signal switch assembly with spiral cable sub-assembly from the steering column assembly.



13. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY

HINT:
Refer to the instructions for Removal of the driver side knee airbag assembly (Click here).



14. REMOVE UPPER INSTRUMENT PANEL ASSEMBLY

HINT:
Refer to the instructions for Removal of the upper instrument panel assembly (Click here).



15. REMOVE BRAKE PEDAL SUPPORT ASSEMBLY (for LHD)

HINT:
Refer to the instructions for Removal of the brake pedal support assembly (Click here).



16. REMOVE BRAKE PEDAL SUPPORT ASSEMBLY (for RHD)

HINT:
Refer to the instructions for Removal of the brake pedal support assembly (Click here).



17. REMOVE NO. 1 HEATER TO REGISTER DUCT


    B223660
  1. Remove the 3 clips and the No. 1 heater to register duct.



18. REMOVE NO. 2 AIR DUCT SUB-ASSEMBLY


    C206263
  1. Disengage the 2 claws to remove the No. 2 air duct sub-assembly.



19. REMOVE COLUMN HOLE COVER SILENCER SHEET


    C206261
  1. Turn back the floor carpet.

  1. Remove the 2 clips and column hole cover silencer sheet.



20. SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY


    C206262E01
  1. Put matchmarks on the No. 2 steering intermediate shaft assembly and steering intermediate shaft.
    Text in Illustration 
    *1
    Matchmark

    NOTICE:
    Do not separate the No. 2 steering intermediate shaft assembly from the steering intermediate shaft.

  1. Remove the bolt.

  1. Separate the No. 2 steering intermediate shaft assembly from the steering intermediate shaft.



21. REMOVE STEERING POST ASSEMBLY


    C206264
  1. Disengage the 2 wire harness clamps.

  1. Disconnect the connector from the power steering ECU assembly.

    HINT:
    As shown in the illustration, turn the lock lever to disconnect the connector.



    C206266
  1. Disconnect the connector from the power steering ECU assembly.

  1. Disconnect the connectors and disengage the wire harness clamps from the steering post assembly.



    C206267
  1. Remove the bolt, 2 nuts and steering post assembly.



22. REMOVE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY


    C206269E01
  1. Put matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly.
    Text in Illustration 
    *1
    Matchmark

  1. Remove the bolt and No. 2 steering intermediate shaft assembly from the steering column assembly.



23. REMOVE NO. 1 STEERING COLUMN PROTECTOR (for RHD)


    C206688
  1. Remove the bolt and No. 1 steering column protector from the steering column assembly.