STEERING COLUMN ASSEMBLY > REMOVAL |
| 1. PRECAUTION |
| 2. PRECAUTION (w/ Navigation System for HDD) |
| 3. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD |
| 4. REMOVE REAR NO. 2 FLOOR BOARD |
![]() |
Disengage the 2 guides <A> as shown in the illustration.
Disengage the 3 guides <B> and remove the rear No. 2 floor board.
| 5. REMOVE REAR DECK FLOOR BOX |
Remove the rear deck floor box.
| 6. REMOVE REAR NO. 3 FLOOR BOARD |
![]() |
Disengage the 2 guides and remove the rear No. 3 floor board.
| 7. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 8. REMOVE STEERING PAD |
| 9. REMOVE STEERING WHEEL ASSEMBLY |
![]() |
Remove the steering wheel assembly set nut.
| *1 | Matchmark |
Put matchmarks on the steering wheel assembly and steering main shaft.
Disconnect the connectors from the spiral cable.
![]() |
Using SST, remove the steering wheel assembly.
| *1 | Turn |
| *2 | Hold |
| 10. REMOVE LOWER STEERING COLUMN COVER |
![]() |
Push the right and left sides of the lower steering column cover to disengage the 4 claws.
![]() |
Insert fingers into the opening of the tilt lever of the lower steering column cover to disengage the 2 claws.
Using a screwdriver, insert the tip into each service hole to disengage the 2 claws to remove the lower steering column cover as shown in the illustration.

| *1 | Service Hole | *2 | Protective Tape |
| 11. REMOVE UPPER STEERING COLUMN COVER |
![]() |
Disengage the 2 claws and 2 pins to remove the upper steering column cover.
| 12. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY |
Disconnect the connectors from the turn signal switch assembly with spiral cable sub-assembly.
![]() |
Using pliers, expand the clamp.
| *1 | Clamp |
| *2 | Claw |
While holding the clamp expanded, raise the claw using a screwdriver to disengage it, and then remove the turn signal switch assembly with spiral cable sub-assembly from the steering column assembly.
| 13. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY |
| 14. REMOVE UPPER INSTRUMENT PANEL ASSEMBLY |
| 15. REMOVE BRAKE PEDAL SUPPORT ASSEMBLY (for LHD) |
| 16. REMOVE BRAKE PEDAL SUPPORT ASSEMBLY (for RHD) |
| 17. REMOVE NO. 1 HEATER TO REGISTER DUCT |
![]() |
Remove the 3 clips and the No. 1 heater to register duct.
| 18. REMOVE NO. 2 AIR DUCT SUB-ASSEMBLY |
![]() |
Disengage the 2 claws to remove the No. 2 air duct sub-assembly.
| 19. REMOVE COLUMN HOLE COVER SILENCER SHEET |
![]() |
Turn back the floor carpet.
Remove the 2 clips and column hole cover silencer sheet.
| 20. SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY |
![]() |
Put matchmarks on the No. 2 steering intermediate shaft assembly and steering intermediate shaft.
| *1 | Matchmark |
Remove the bolt.
Separate the No. 2 steering intermediate shaft assembly from the steering intermediate shaft.
| 21. REMOVE STEERING POST ASSEMBLY |
![]() |
Disengage the 2 wire harness clamps.
Disconnect the connector from the power steering ECU assembly.
![]() |
Disconnect the connector from the power steering ECU assembly.
Disconnect the connectors and disengage the wire harness clamps from the steering post assembly.
![]() |
Remove the bolt, 2 nuts and steering post assembly.
| 22. REMOVE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY |
![]() |
Put matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly.
| *1 | Matchmark |
Remove the bolt and No. 2 steering intermediate shaft assembly from the steering column assembly.
| 23. REMOVE NO. 1 STEERING COLUMN PROTECTOR (for RHD) |
![]() |
Remove the bolt and No. 1 steering column protector from the steering column assembly.