Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM (w/ EGR System)

DTC    P2A00    A/F Sensor Circuit Slow Response (Bank 1 Sensor 1)

for Preparation Click here


DESCRIPTION

Refer to DTC P2195 .

DTC No.
DTC Detection Condition
Trouble Area
P2A00
Calculated value for air fuel ratio sensor response rate deterioration level is less than threshold
(2 trip detection logic)
  1. Air fuel ratio sensor (sensor 1)
  2. EGR valve assembly
  3. ECM

CONFIRMATION DRIVING PATTERN

HINT:
Performing this confirmation pattern will activate the air fuel ratio sensor response monitor.


A207867E08

  1. Connect the intelligent tester to the DLC3.
  2. Turn the power switch on (IG).
  3. Turn the tester on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Put the engine in inspection mode (Click here).
  6. Start the engine and warm it up (until the engine coolant temperature is 75°C (167°F) or more) [B].
  7. Drive the vehicle at a constant speed of between 75 and 100 km/h (47 and 62 mph) for 10 minutes [C].
  8. Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.
  9. Read the pending DTC [D].

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P2A00.
  12. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    UNKNOWN
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.


WIRING DIAGRAM

Refer to DTC P2195 .

INSPECTION PROCEDURE

HINT:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the intelligent tester.
  1. Connect the intelligent tester to the DLC3.
  2. Turn the power switch on (IG).
  3. Turn the tester on.
  4. Put the engine in inspection mode (Click here).
  5. Start the engine.
  6. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  7. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
  8. Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
  9. Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the tester.

HINT:
  1. The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  1. Each sensor reacts in accordance with increases in the fuel injection volume.


Tester Display
(Sensor)
Injection Volume
Status
Voltage
AFS Voltage B1S1
(Air fuel ratio)
+25%
Rich
Less than 3.1 V
AFS Voltage B1S1
(Air fuel ratio)
-12.5%
Lean
More than 3.4 V
O2S B1S2
(Heated oxygen)
+25%
Rich
More than 0.55 V
O2S B1S2
(Heated oxygen)
-12.5%
Lean
Less than 0.4 V

NOTICE:
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


Case
Air Fuel Ratio Sensor (Sensor 1)
Output Voltage
Heated Oxygen Sensor (Sensor 2)
Output Voltage
Main Suspected Trouble Area
1
A162605E12
A162598E12
-
2
A162596E06
A162598E12
  1. Air fuel ratio sensor
  2. Air fuel ratio sensor heater
  3. Air fuel ratio sensor circuit
3
A162605E12
A162596E07
  1. Heated oxygen sensor
  2. Heated oxygen sensor heater
  3. Heated oxygen sensor circuit
  4. Exhaust gas leaks
4
A162596E06
A162596E06
  1. Fuel pressure
  2. Exhaust gas leaks
    (Air fuel ratio extremely lean or rich)
  1. Performing Control the Injection Volume for A/F Sensor enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensors.
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2.

HINT:
  1. Sensor 1 refers to the sensor mounted in front of the Three-way Catalytic Converter (TWC) and located near the engine assembly.
  2. DTC P2A00 may also be set when the air fuel ratio remains rich or lean.
  3. A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.
  4. A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.
  5. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  6. Sensor 1 refers to the sensor closest to the engine assembly.
  7. Sensor 2 refers to the sensor farthest away from the engine assembly.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2A00)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC P2A00 is output
    A
    DTC P2A00 and other DTCs are output
    B

HINT:
If any DTCs relating to the air fuel ratio sensor (DTCs for the air fuel ratio sensor heater or air fuel ratio sensor admittance) are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION VOLUME)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Put the engine in inspection mode (Click here).

  1. Start the engine.

  1. Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.

  1. Perform the Control the Injection Volume operation with the engine idling.

  1. Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the tester.

    HINT:
    1. Change the fuel injection volume within the range of - 12.0% to +12.0%. The injection volume can be changed in fine gradations.
    2. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
    3. If there is almost no response from the air fuel ratio sensor, a malfunction of the air fuel ratio sensor is suspected


    Tester Display (Sensor)
    Injection Volume
    Status
    Voltage
    AFS Voltage B1S1
    (Air fuel ratio)
    +12%
    Rich
    Below 3.1 V
    AFS Voltage B1S1
    (Air fuel ratio)
    -12%
    Lean
    Higher than 3.4 V
    O2S B1S2
    (Heated oxygen)
    +12%
    Rich
    Higher than 0.55 V
    O2S B1S2
    (Heated oxygen)
    -12%
    Lean
    Below 0.4 V

    Result:

    Status of AFS Voltage B1S1
    Status of O2S B1S2
    Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition
    Misfire
    Suspected Trouble Area
    Proceed to
    Lean/Rich
    Lean/Rich
    Normal
    -
    -
    A
    Lean
    Lean
    Actual air fuel ratio lean
    May occur
    1. PCV valve and hose
    2. PCV hose connections
    3. Fuel injector assembly blockage
    4. Gas leaks from exhaust system
    5. Intake system
    6. Fuel pressure
    7. Mass air flow meter sub-assembly
    8. Manifold absolute pressure sensor
    9. Engine coolant temperature sensor
    10. EGR valve assembly
    B
    Rich
    Rich
    Actual air fuel ratio rich
    -
    1. Fuel injector assembly leakage or blockage
    2. Gas leaks from exhaust system
    3. Ignition system
    4. Fuel pressure
    5. Mass air flow meter sub-assembly
    6. Manifold absolute pressure sensor
    7. Engine coolant temperature sensor
    B
    Lean
    Lean/Rich
    Air fuel ratio sensor malfunction
    -
    1. Air fuel ratio sensor
    2. EGR valve assembly
    C
    Rich
    Lean/Rich
    Air fuel ratio sensor malfunction
    -
    Air fuel ratio sensor
    C

    Lean: During the Control the Injection Volume Active Test, the air fuel ratio sensor output voltage (AFS Voltage) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S) is consistently below 0.4 V.
    Rich: During the Control the Injection Volume Active Test, the AFS Voltage is consistently below 3.1 V, and the O2S is consistently higher than 0.55 V.
    Lean/Rich: During the Control the Injection Volume Active Test, the output voltage of the heated oxygen sensor alternates correctly.

  1. Refer to "Data List / Active Test" [AFS Voltage B1S1 and O2S B1S2] (Click here).



B
Go to step 4

C
Go to step 8
A


3.PERFORM CONFIRMATION DRIVING PATTERN
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the power switch off and wait for 30 seconds.

  1. Turn the power switch on (IG) and turn the tester on.

  1. Put the engine in inspection mode (Click here).

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P2A00.

  1. Check the DTC judgment result.

    Result 
    Result
    Proceed to
    NORMAL (DTC is not output)
    A
    ABNORMAL (DTC P2A00 is output)
    B



A
CHECK FOR INTERMITTENT PROBLEMS (Click here)

B
Go to step 8

4.INSPECT AIR FUEL RATIO SENSOR NO.2 (HEATER RESISTANCE)
  1. Inspect the air fuel ratio sensor (Click here).



NG
REPLACE AIR FUEL RATIO SENSOR NO.2 (Click here)
OK


5.CHECK INTAKE SYSTEM
  1. Check the intake system (Click here).



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


6.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
Go to step 14
OK


7.INSPECT FUEL INJECTOR ASSEMBLY
  1. Inspect the fuel injector assembly (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


8.REPLACE AIR FUEL RATIO SENSOR NO.2
  1. Replace the air fuel ratio sensor (Click here).


NEXT


9.PERFORM CONFIRMATION DRIVING PATTERN
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the power switch off and wait for 30 seconds.

  1. Turn the power switch on (IG) and turn the tester on.

  1. Put the engine in inspection mode (Click here).

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P2A00.

  1. Check the DTC judgment result.

    Result 
    Result
    Proceed to
    ABNORMAL (DTC P2A00 is output)
    A
    NORMAL (DTC is not output)
    B



B
END
A


10.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE EGR STEP POSITION)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Put the engine in inspection mode (Click here).

  1. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or more.

    HINT:
    The A/C switch and all accessory switches should be off.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.

  1. Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.

    HINT:
    1. Do not leave the EGR valve open for 10 seconds or more during Active Test.
    2. Be sure to return the EGR valve to step 0 when Active Test is completed.

    OK:
    MAP and idling condition change in response to EGR step position when Throttle Idle Position is ON in Data List.


    Standard:

    -
    EGR Step Position (Active Test)
    0 Steps
    0 to 30 Steps
    Idling condition
    Steady idling
    Idling changes from steady to rough idling or engine stall
    MAP
    (Data List)
    20 to 40 kPa (150 to 300 mmHg)
    (EGR valve is fully closed)
    MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed

    HINT:
    During Active Test, if the idling condition does not change in response to EGR step position, then there is probably a malfunction in EGR valve.



OK
Go to step 12

NG
Go to step 11

11.INSPECT EGR VALVE ASSEMBLY
  1. Remove the EGR valve assembly (Click here).

  1. Check if the EGR valve is stuck open.

    OK:
    EGR valve is tightly closed.

  1. Reinstall the EGR valve assembly (Click here).



NG
REPLACE EGR VALVE ASSEMBLY (Click here)
OK


12.REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


13.PERFORM CONFIRMATION DRIVING PATTERN
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the power switch off and wait for 30 seconds.

  1. Turn the power switch on (IG) and turn the tester on.

  1. Put the engine in inspection mode (Click here).

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P2A00.

  1. Check that the DTC judgment result is NORMAL.


NEXT

END 

14.INSPECT FUEL PUMP
  1. Inspect the fuel pump (Click here).



NG
REPLACE FUEL PUMP (Click here)
OK

REPAIR OR REPLACE FUEL LINE