ENTRY AND START SYSTEM (for Entry Function) > SYSTEM DESCRIPTION |
| ENTRY AND START SYSTEM DESCRIPTION |
In addition to conventional mechanical key and wireless door lock control functions, the entry and start system enables door locking/unlocking and hybrid vehicle control system starting without operating the key. The only requirement is that the key is in the user's possession.
| DETECTION AREA |
w/ Entry System Back Door Open Function

| Actuation Area | Detail |
| Interior | The interior detection area of the indoor electrical key oscillators (for front, center and rear floor) is formed when the driver door is opened or closed, when the power switch is pushed, when a warning is activated, or when the lock sensor on the door outside handle assembly or lock switch on the back door opener switch assembly is on. |
| Exterior | The exterior detection area formed by the door electrical key oscillators (for driver side and front passenger side) and outside electrical key oscillator (for rear side) is approximately 0.7 to 1.0 m (2.30 to 3.28 ft.) from the door outside handle assembly of the front doors, or the center of the rear bumper. |
| Around Front Door | The exterior detection area of the door electrical key oscillator (for driver side or front passenger side) is formed by transmitting a request signal every 0.25 seconds while the power switch is off and each door is locked. In this way it detects the proximity of a key. When locking the door using the lock sensor on the door outside handle assembly, the detection area is formed when the lock sensor is touched. |
| Around Back Door | The exterior detection area of the outside electrical key oscillator (for rear side) is formed by when the back door opener switch assembly (opener or lock switch) is on. |
w/o Entry System Back Door Open Function

| Actuation Area | Detail |
| Interior | The interior detection area of the indoor electrical key oscillators (for front, center and rear floor) is formed when the driver door is opened or closed, when the power switch is pushed, when a warning is activated, or when the lock sensor on the door outside handle assembly or lock switch on the back door opener switch assembly is on. |
| Exterior | The exterior detection area formed by the door electrical key oscillators (for driver side) is approximately 0.7 to 1.0 m (2.30 to 3.28 ft.) from the door outside handle assembly of the front doors, or the center of the rear bumper. |
| Around Front Door | The exterior detection area of the door electrical key oscillator (for driver side) is formed by transmitting a request signal every 0.25 seconds while the power switch is off and each door is locked. In this way it detects the proximity of a key. When locking the door using the lock sensor on the door outside handle assembly, the detection area is formed when the lock sensor is touched. |
| FUNCTION OF MAIN COMPONENTS |
| Component | Function | |
| Key |
| |
| Certification ECU (Smart Key ECU Assembly) |
| |
| Main Body ECU (Multiplex Network Body ECU) |
| |
| Front Door Outside Handle Assembly (for Driver Side, Front Passenger Side*2) (touch sensor) | Sends a door unlock request signal to the certification ECU (smart key ECU assembly) when the touch sensor on the inner side of the front door outside handle assembly is touched. | |
| Front Door Outside Handle Assembly (for Driver Side, Front Passenger Side*2) (lock sensor) | Sends a door lock request signal to the certification ECU (smart key ECU assembly) when the lock sensor on the front door outside handle assembly is touched. | |
| Door Electrical Key Oscillator (for Driver Side, Front Passenger Side*2) | Receives the request signal from the certification ECU (smart key ECU assembly), and creates an detection area around the front doors. | |
| Indoor Electrical Key Oscillator (for Front, Center and Rear Floor) | Receives a request signal from the certification ECU (smart key ECU assembly) and forms the interior detection area. | |
| Outside Electrical Key Oscillator (for Rear Side)*2 | Receives the request signal from the certification ECU (smart key ECU assembly), and forms an detection area around the back door. | |
| Door Control Receiver Assembly | Receives the ID code from the key and transmits it to the certification ECU (smart key ECU assembly). | |
Back Door Opener Switch Assembly*2
| Transmits a back door open request signal to the certification ECU (smart key ECU assembly). | |
Back Door Opener Switch Assembly*2
| Transmits a back door lock request signal to the certification ECU (smart key ECU assembly). | |
| Stop Light Switch | Outputs state of the brake pedal to the power management control ECU. | |
| Combination Meter Assembly | Buzzer | Sounds to inform the driver of malfunctions in the entry and start system. |
| Multi-information Display | The following warning messages appear to alert the driver:
| |
| Wireless Door Lock Buzzer Assembly | Sounds to inform the driver of malfunctions in the entry and start system. | |
| CONSTRUCTION AND OPERATION |
Key
The key consists of a mechanical key, transmitter for wireless door lock control and transceiver for the entry and start system.
Key (w/ Remote Air Conditioning System):

Key (w/o Remote Air Conditioning System):

Key (w/ Panic Switch):

Oscillator (door electrical key oscillator (for driver side and front passenger side*), indoor electrical key oscillator (for front, center and rear floors) and outside electrical key oscillator (for rear side)*)
Each oscillator transmits the request signal received from the certification ECU (smart key ECU assembly), and forms a key detection area to detect the presence of a key. The detection area formed by door electrical key oscillator (for driver side and front passenger side*) and outside electrical key oscillator (for rear side)* is approximately 0.7 to 1.0 m (2.30 to 3.28 ft.) from the door outside handle assembly of door (for driver side, front passenger side*) or the center of the rear bumper.
*: w/ Entry System Back Door Open Function
| ENTRY FUNCTION OPERATION |
The entry and start system has the following functions:
| Function | Outline |
| Wireless Door Lock Control | This function is a convenient system for locking and unlocking all the doors and back door at a distance. The operation of this function is the same as that in the wireless door lock control system. |
| Entry Unlock | When a key is in the exterior detection area of any door electrical key oscillator, the door will unlock after the inner side of front door outside handle assembly (for driver side or front passenger side*) is touched. |
| Entry Lock |
|
| Entry System Back Door Open Function* | When a key is in the exterior detection area of the outside electrical key oscillator (for rear side), the back door opens manually by simply pressing the back door opener switch assembly (opener switch). |
| Prevention of Key Confinement | The key confinement prevention function prevents the vehicle from being locked with a key left inside. |
| Warning | When any of the situations below occur, the entry and start system causes the certification ECU (smart key ECU assembly) to sound the buzzer in the combination meter assembly and wireless door lock buzzer assembly, and indicate a warning on the multi-information display in order to alert the driver:
|
| Battery Saving | If the key remains within the exterior detection area of any electrical key oscillator (for driver, front passenger or rear side), the system maintains periodic communication with the key. Therefore, if the vehicle remains parked in that state for a long time, the key battery and the vehicle battery could be drained. |
| Key Cancel (Click here) | The following key functions can be cancelled by following certain procedures:
|
| Key Code Registration | A total of 7 keys can be registered. This function enables the registration (writing and storing) of transmitter recognition codes in the EEPROM that is contained in the certification ECU (smart key ECU assembly). |
| WIRELESS DOOR LOCK CONTROL SYSTEM FUNCTION |
| ENTRY UNLOCK FUNCTION |
When the key enters any exterior detection area of a front door, the certification ECU (smart key ECU assembly) judges and certifies the key ID code received from the door control receiver assembly.
After the key certification OK is confirmed, the certification ECU (smart key ECU assembly) transmits an unlock stand-by signal to the touch sensor of the relevant door.
If a touch sensor is touched in this condition, the certification ECU (smart key ECU assembly) transmits a door unlock request signal to the main body ECU (multiplex network body ECU), and unlocks all doors.
The main body ECU (multiplex network body ECU) sounds the wireless door lock buzzer twice*, and the main body ECU (multiplex network body ECU) flashes the hazard warning lights twice, as an answer back for entry unlock.
*: w/o Airbag Cut-off Switch
| ENTRY LOCK FUNCTION |
The entry lock signal is transmitted to the certification ECU (smart key ECU assembly) when the user (who has the key in their possession) exits the vehicle and touches the lock senor on the door outside handle assembly or presses the lock switch on the back door opener switch assembly*.
*: w/ Entry System Back Door Open Function
The certification ECU (smart key ECU assembly) transmits a request signal for the indoor electrical key oscillators (for front, center and rear floor), door electrical key oscillators (for driver side and front passenger side*) and outside electrical key oscillator (for rear side)* to form detection areas.
*: w/ Entry System Back Door Open Function
The certification ECU (smart key ECU assembly) judges and certifies the ID code. It then checks the location of the key, and if all doors are closed, the ECU transmits a door lock signal to the main body ECU (multiplex network body ECU).
The main body ECU (multiplex network body ECU) receives this signal and actuates the lock motors.
The main body ECU (multiplex network body ECU) blinks the hazard warning lights once and the main body ECU (multiplex network body ECU) sounds the wireless door lock buzzer once* as an answerback for the entry lock function.
*: w/o Airbag Cut-off Switch
| ENTRY SYSTEM BACK DOOR OPEN FUNCTION* |
The unlock signal is transmitted to the certification ECU (smart key ECU assembly) from the back door opener switch assembly.
The certification ECU (smart key ECU assembly) transmits a request signal for the outside electrical key oscillator (for rear side) to form a detection area.
The key receives this signal and returns the ID code to the door control receiver assembly.
The certification ECU (smart key ECU assembly) judges and certifies the ID code, and check the location of the key. The ECU transmits a back door open signal to the main body ECU (multiplex network body ECU).
Any ECU receives this signal and actuates the motor to open manually the back door.
| PREVENTION OF KEY CONFINEMENT FUNCTION |
The key confinement prevention function prevents the key from being locked in the vehicle.
When the door is locked by the lock knob in the inside door handle while the key is still in the vehicle interior, the main body ECU (multiplex network body ECU) receives this signal and transmits the door condition signal to the certification ECU (smart key ECU assembly).
The certification ECU (smart key ECU assembly) transmits a request signal for the indoor electrical key oscillators (for front, center and rear floor) to form detection areas.
The key receives this signal and returns the ID code to the door control receiver assembly.
The certification ECU (smart key ECU assembly) judges and certifies the ID code, and check the location of the key. The ECU transmits a door unlock signal to the main body ECU (multiplex network body ECU).
The main body ECU (multiplex network body ECU) receives this signal and actuates the all door lock assemblies to unlock.
The certification ECU (smart key ECU assembly) sounds the wireless door lock buzzer* and buzzer in the combination meter as an answer back for unlock.
*: w/ Airbag Cut-off Switch
| WARNING FUNCTION |
Warning
When any of the situations below occur, the entry and start system causes the certification ECU (smart key ECU assembly) to sound a buzzer in the combination meter assembly and the wireless door lock buzzer assembly, a message to appear on the multi-information display, and the power switch illumination to operate in order to alert the driver.
| Situation | Condition |
| A | The hybrid vehicle control system is left running and the shift lever is in R, N, D or B when the driver gets out of the vehicle. |
| B | The key reminder sounds. |
| C | The hybrid vehicle control system is left running and park (P) is selected when the driver gets out of the vehicle. |
| D | A door is ajar. |
| E | The hybrid vehicle control system is left running when a passenger gets out of the vehicle while holding the key. |
| F | The key is not in the detection areas. |
| G | The key is left in the vehicle. |
| H | The key battery is weak. |
| I | The power management ECU is malfunctioning. |
| J | The hybrid vehicle control system cannot be started (driver error). |
| K | The hybrid vehicle control system cannot be started (system error). |
| L | An attempt is made to turn off the vehicle with the shift lever in a R, D or B. |
| M | Auto power off operation occurs. |
| N | Immobiliser system certification completion occurs. |
| O | The vehicle is driven without a key. |
Situation A
| Possible Effects without Warning | Sudden vehicle start, vehicle theft, vehicle roll-away | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds continuously |
| Multi-information Display | The following warning message is displayed:
| ||
| Wireless Door Lock Buzzer Assembly | - | ||
| Power Switch Illumination | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
| Possible Effects without Warning | Sudden vehicle start, vehicle theft, vehicle roll-away | |||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| |||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds continuously | |
| Multi-information Display | The following warning messages are alternately displayed:
| |||
| Wireless Door Lock Buzzer Assembly | Sounds continuously | |||
| Power Switch Illumination | - | |||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met: | |||
| Combination Meter Assembly | Buzzer |
| ||
| Multi-information Display | The following warning message is displayed:
|
| ||
The following warning message is displayed:
|
| |||
| Wireless Door Lock Buzzer Assembly |
| |||
Situation B
| Possible Effects without Warning | Vehicle theft | ||
| Warning Active Condition | The warning is activated when either of the following patterns is met:
| ||
| Waning Method | Combination Meter Assembly | Buzzer | Sounds continuously at short and even intervals |
| Multi-information Display | - | ||
| Wireless Door Lock Buzzer Assembly | - | ||
| Power Switch Illumination | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
Situation C
| Possible Effects without Warning | Vehicle theft, hybrid vehicle control system cannot be restarted, discharged battery | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed:
| ||
| Wireless Door Lock Buzzer Assembly | Sounds 3 times | ||
| Power Switch Illumination | - | ||
| Warning Stop Condition | The warning is stopped when either of the following conditions is met:
| ||
| Possible Effects without Warning | Vehicle theft, discharged battery | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed for 60 seconds (and then automatically turned off).
| ||
| Wireless Door Lock Buzzer Assembly | Sounds continuously | ||
| Power Switch Illumination | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met: | ||
| Combination Meter Assembly | Multi-information Display |
| |
| Wireless Door Lock Buzzer Assembly |
| ||
Situation D
| Possible Effects without Warning | Vehicle theft | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | - |
| Multi-information Display | - | ||
| Wireless Door Lock Buzzer Assembly | Sounds continuously | ||
| Power Switch Illumination | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
Situation E
| Possible Effect without Warning | Hybrid vehicle control system cannot be restarted | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed:
| ||
| Wireless Door Lock Buzzer Assembly | Sounds 3 times | ||
| Power Switch Illumination | - | ||
| Warning Stop Condition | The warning is stopped when either of the following conditions is met:
| ||
Situation F
| Possible Effects without Warning | Confuses the user | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed for 15 seconds (and then automatically turned off).
| ||
| Wireless Door Lock Buzzer Assembly | - | ||
| Power Switch Illumination | - | ||
| Warning Stop Condition | Check if the key is in the detection area. If the key is in the detection area, press the wireless door lock switch and confirm that the indicator comes on. If the indicator does not come on, replace the key battery with a new one. | ||
Situation G
| Possible Effect without Warning | Vehicle theft | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | - |
| Multi-information Display | The following warning message is displayed for 60 seconds (and then automatically turned off).
| ||
| Wireless Door Lock Buzzer Assembly | Sounds continuously | ||
| Power Switch Illumination | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met: | ||
| Combination Meter Assembly | Multi-information Display |
| |
| Wireless Door Lock Buzzer Assembly |
| ||
| Possible Effect without Warning | Vehicle theft | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | - |
| Multi-information Display | The following warning message is displayed for 60 seconds (and then automatically turned off).
| ||
| Wireless Door Lock Buzzer Assembly | Sounds continuously | ||
| Power Switch Illumination | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met: | ||
| Combination Meter Assembly | Multi-information Display |
| |
| Wireless Door Lock Buzzer Assembly |
| ||
Situation H
| Possible Effect without Warning | Entry and start system does not function | ||
| Warning Active Condition | The warning is activated when both of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | - |
| Multi-information Display | The following warning message is displayed for 15 seconds (and then automatically turned off).
| ||
| Wireless Door Lock Buzzer Assembly | - | ||
| Power Switch Illumination | - | ||
| Warning Stop Condition | The key battery is replaced with a new one. | ||
Situation I
| Possible Effect without Warning | Malfunction detection | ||
| Warning Active Condition | A malfunction of the power management ECU is detected. | ||
| Warning Method | Combination Meter Assembly | Buzzer | - |
| Multi-information Display | - | ||
| Wireless Door Lock Buzzer Assembly | - | ||
| Power Switch Illumination | The amber indicator blinks at 2-second intervals (goes off automatically after 15 seconds). | ||
| Warning Stop Condition | The power management control ECU returns to normal. | ||
Situation J
| Possible Effects without Warning | Usability function | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | - |
| Multi-information Display | The following warning message is displayed for 10 seconds (and then automatically turned off).
| ||
| Wireless Door Lock Buzzer Assembly | - | ||
| Power Switch Illumination | - | ||
| Warning Stop Condition | The power switch is pushed with the brake pedal depressed. | ||
| Possible Effects without Warning | Usability function | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | - |
| Multi-information Display | The following warning message is displayed:
| ||
| Wireless Door Lock Buzzer Assembly | - | ||
| Power Switch Illumination | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
Situation K
| Possible Effects without Warning | Usability function | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed for 60 seconds (and then automatically turned off).
| ||
| Wireless Door Lock Buzzer Assembly | - | ||
| Power Switch Illumination | - | ||
| Warning Stop Condition | The warning is stopped when either of the following conditions is met:
| ||
| Possible Effects without Warning | Usability function | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed for 60 seconds (and then automatically turned off).
| ||
| Wireless Door Lock Buzzer Assembly | - | ||
| Power Switch Illumination | - | ||
| Warning Stop Condition | The warning is stopped when either of the following conditions is met:
| ||
Situation L
| Possible Effects without Warning | Usability function | ||
| Warning Active Condition | The warning is activated when both of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | - |
| Multi-information Display | The following warning message is displayed:
| ||
| Wireless Door Lock Buzzer Assembly | - | ||
| Power Switch Illumination | - | ||
| Warning Stop Condition | The warning is stopped when either of the following conditions is met:
| ||
Situation M
| Possible Effects without Warning | Battery Saving function | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | - |
| Multi-information Display | The following warning message is displayed for 10 seconds (and then automatically turned off).
| ||
| Wireless Door Lock Buzzer Assembly | - | ||
| Power Switch Illumination | - | ||
| Warning Stop Condition | The power switch is turned to a mode other than off. | ||
Situation N
| Possible Effects without Warning | Malfunction detection | ||
| Warning Active Condition | Key certification result is OK.* | ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed for 10 seconds (and then automatically turned off).
| ||
| Wireless Door Lock Buzzer Assembly | - | ||
| Power Switch Illumination | The amber indicator blinks | ||
| Warning Stop Condition | The warning is stopped when either of the following conditions is met:
| ||
Situation O
| Possible Effects without Warning | Hybrid vehicle control system cannot be restarted | ||
| Warning Active Condition | When vehicle speed is detected after the key is removed from the vehicle, the warning is activated (only for first time). | ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed:
| ||
| Wireless Door Lock Buzzer Assembly | - | ||
| Power Switch Illumination | - | ||
| Warning Stop Condition | The warning is stopped when either of the following conditions is met:
| ||
| BATTERY SAVING |
Vehicle Battery Saving Function
In the entry and start system, signals are emitted outside the vehicle at a prescribed interval (0.25 seconds) when the doors are locked. Therefore, the vehicle battery could be drained if the vehicle remains parked for a long time. For this reason, the controls listed below are affected:
| Condition | Control |
Both conditions below are met for 5 days:
| Signal transmission interval is extended from 0.25 to 0.75 seconds |
Both conditions below are met for 14 days:
| The entry and start system is automatically deactivates |
Key Battery and Vehicle Battery Saving Function
In the entry and start system, if the key is constantly in the exterior detection area of the doors, the system maintains periodic communication with the key. Therefore, if the vehicle remains parked in that state for a long time, the key battery and vehicle battery could be drained. For this reason, if this state continues longer than 10 minutes, the entry and start system automatically becomes deactivated.
Reinstatement Conditions