Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM

DTC    U0235    Lost Communication with Cruise Control Front Distance Range Sensor

for Preparation Click here


DESCRIPTION

The millimeter wave radar sensor and driving support ECU transmit the data for general vehicle control and diagnosis function along the communication line. The millimeter wave radar sensor assembly transmits information about the vehicle in front to the driving support ECU.

DTC No.
DTC Detection Condition
Trouble Area
U0235
The seat belt control ECU detects a communication error signal (from the millimeter wave radar sensor assembly to the driving support ECU) for 1 second or more while the dynamic radar cruise control is operating
  1. Millimeter wave radar sensor assembly
  2. Millimeter wave radar sensor circuit
  3. Driving support ECU

WIRING DIAGRAM


A219430E01


INSPECTION PROCEDURE

NOTICE:
When the millimeter wave radar sensor is replaced with a new one, adjustment of the radar sensor beam axis must be performed (Click here).

1.CHECK CAN COMMUNICATION SYSTEM
  1. Select "CAN Bus Check" from "System Selection Menu" screen on the intelligent tester.

  1. Select "Communication Malfunction DTC" from the "CAN Bus Check" screen, and then select "Enter".

    OK:
    Communication system is normal.



NG
GO TO CAN COMMUNICATION SYSTEM (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR POWER SOURCE)


    E168714E13
  1. Disconnect the millimeter wave radar sensor assembly connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A2-5 (IGB) - Body ground
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Millimeter Wave Radar Sensor Assembly)

  1. Reconnect the millimeter wave radar sensor assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - IG1 NO. 1 RELAY)
OK


3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)


    E168714E14
  1. Disconnect the millimeter wave radar sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A2-2 (SGND) - Body ground
    Always
    Below 1 Ω
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Millimeter Wave Radar Sensor Assembly)

  1. Reconnect the millimeter wave radar sensor assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)
OK


4.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
  1. Replace the millimeter wave radar sensor assembly (Click here).

  1. Adjust the millimeter wave radar sensor assembly (Click here).


NEXT


5.CHECK WHETHER DTC OUTPUT RECURS (DTC U0235)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Clear the DTCs (Click here).

  1. Perform the following to make sure that the DTC detection conditions are met.

    HINT:
    If the detection conditions are not met, the malfunction cannot be detected.

    1. Drive the vehicle at a speed of 40 km/h (25 mph) or more.

    2. Turn the cruise control main switch on.

    3. Push the -SET switch to activate the cruise control.

  1. Enter the following menus: Powertrain / Radar Cruise / DTC.

  1. Read the DTCs.

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC U0235 is output
    B



B
REPLACE DRIVING SUPPORT ECU (Click here)
A

END