Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM (w/o EGR System)

SFI SYSTEM (w/o EGR System) > Fuel Injector Circuit

for Preparation Click here


DESCRIPTION

The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.

WIRING DIAGRAM


A269329E01


INSPECTION PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)


    A194105E37
  1. Disconnect the fuel injector assembly connectors.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D14-1 - Body ground
    Power switch on (IG)
    11 to 14 V
    D15-1 - Body ground
    Power switch on (IG)
    11 to 14 V
    D16-1 - Body ground
    Power switch on (IG)
    11 to 14 V
    D17-1 - Body ground
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Injector Assembly)

  1. Reconnect the fuel injector assembly connectors.



NG
Go to step 4
OK


2.INSPECT FUEL INJECTOR ASSEMBLY
  1. Inspect the fuel injector assembly (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
  1. Disconnect the fuel injector assembly connectors.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    D14-2 - D28-85 (#10)
    Always
    Below 1 Ω
    D15-2 - D28-84 (#20)
    Always
    Below 1 Ω
    D16-2 - D28-83 (#30)
    Always
    Below 1 Ω
    D17-2 - D28-82 (#40)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    D14-2 or D28-85 (#10) - Body ground
    Always
    10 Ω or higher
    D15-2 or D28-84 (#20) - Body ground
    Always
    10 Ω or higher
    D16-2 or D28-83 (#30) - Body ground
    Always
    10 Ω or higher
    D17-2 or D28-82 (#40) - Body ground
    Always
    10 Ω or higher

  1. Reconnect the fuel injector assembly connectors.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

4.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - NO. 2 INTEGRATION RELAY (IG2 RELAY))
  1. Disconnect the fuel injector assembly connectors.

  1. Remove the No. 2 integration relay from the engine room relay block and junction block assembly.

  1. Disconnect the No. 2 integration relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    D14-1 - 1A-4
    Always
    Below 1 Ω
    D15-1 - 1A-4
    Always
    Below 1 Ω
    D16-1 - 1A-4
    Always
    Below 1 Ω
    D17-1 - 1A-4
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    D14-1 or 1A-4 - Body ground
    Always
    10 kΩ or higher
    D15-1 or 1A-4 - Body ground
    Always
    10 kΩ or higher
    D16-1 or 1A-4 - Body ground
    Always
    10 kΩ or higher
    D17-1 or 1A-4 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the fuel injector assembly connectors.

  1. Reconnect the No. 2 integration relay connector.

  1. Reinstall the No. 2 integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL INJECTOR ASSEMBLY - NO. 2 INTEGRATION RELAY (IG2 RELAY))
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)