Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for HDD)

NAVIGATION SYSTEM (for HDD) > Steering Pad Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the navigation receiver assembly.
If there is an open in the circuit, the navigation system cannot be operated using the steering pad switch assembly.
If there is a short in the circuit, the resulting condition is the same as to if the switch were continuously pressed. Therefore, the navigation receiver assembly cannot be operated using the steering pad switch assembly, and the navigation receiver assembly itself cannot function.

WIRING DIAGRAM


Before October, 2010

E176601E12


From October, 2010

E250442E25


INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with an SRS (Supplemental Restraint System). Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (Click here).

1.INSPECT NAVIGATION RECEIVER ASSEMBLY


    E168561E44
  1. Disconnect the L109 navigation receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    L109-7 (SW1) - L109-6 (SWG)
    No switch pushed
    95 to 105 kΩ
    L109-7 (SW1) - L109-6 (SWG)
    Seek+ switch pushed
    Below 2.5 Ω
    L109-7 (SW1) - L109-6 (SWG)
    Seek- switch pushed
    323 to 335 Ω
    L109-7 (SW1) - L109-6 (SWG)
    Volume+ switch pushed
    980 to 1020 Ω
    L109-7 (SW1) - L109-6 (SWG)
    Volume- switch pushed
    3048 to 3172 Ω
    L109-8 (SW2) - L109-6 (SWG)
    No switch pushed
    95 to 105 kΩ
    L109-8 (SW2) - L109-6 (SWG)
    MODE switch pushed
    Below 2.5 Ω
    L109-8 (SW2) - L109-6 (SWG)
    Voice switch pushed
    3048 to 3172 Ω
    L109-8 (SW2) - L109-6 (SWG)
    On Hook switch pushed
    323 to 335 Ω
    L109-8 (SW2) - L109-6 (SWG)
    Off Hook switch pushed
    980 to 1020 Ω

Text in Illustration 
*1
Front view of wire harness connector
(to Navigation Receiver Assembly)


NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY


    E187114E01
  1. Disconnect the steering pad switch assembly and spiral with sensor cable sub-assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z9-8 (EAU) - L52-4 (EAU)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z9-10 (AU1) - L52-6 (AU1)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z9-9 (AU2) - L52-5 (AU2)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    NOTICE:
    The spiral with sensor cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral with sensor cable sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.

    HINT:
    1. Removal (Click here)
    2. Installation (Click here)

Text in Illustration 
*1
Component without harness connected
(Spiral with Sensor Cable Sub-assembly)
*2
Steering Pad Switch Assembly Side
*3
Vehicle Side


NG
REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (Click here)
OK


3.INSPECT STEERING PAD SWITCH ASSEMBLY


  1. Disconnect the z9 steering pad switch assembly connector.


    E187366E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Switch Condition
    Specified Condition
    z9-10 (AU1) - z9-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    z9-10 (AU1) - z9-8 (EAU)
    Seek+ switch pushed
    Below 2.5 Ω
    z9-10 (AU1) - z9-8 (EAU)
    Seek- switch pushed
    323 to 335 Ω
    z9-10 (AU1) - z9-8 (EAU)
    Volume+ switch pushed
    980 to 1020 Ω
    z9-10 (AU1) - z9-8 (EAU)
    Volume- switch pushed
    3048 to 3172 Ω
    z9-9 (AU2) - z9-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    z9-9 (AU2) - z9-8 (EAU)
    MODE switch pushed
    Below 2.5 Ω
    z9-9 (AU2) - z9-8 (EAU)
    Voice switch pushed
    3048 to 3172 Ω
    z9-9 (AU2) - z9-8 (EAU)
    On Hook switch pushed
    323 to 335 Ω
    z9-9 (AU2) - z9-8 (EAU)
    Off Hook switch pushed
    980 to 1020 Ω


Text in Illustration 
*1
Component without harness connected
(Steering Pad Switch Assembly)
*2
Volume+
*3
Volume-
*4
MODE
*5
Seek-
*6
Voice Switch
*7
Off Hook
*8
Seek+
*9
On Hook
-
-
  1. Proceed to the next step based on the inspection result.

    Result:
    Result
    Proceed to
    NG (From October, 2010)
    A
    NG (Before October, 2010)
    B
    OK
    C



B
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR (NAVIGATION RECEIVER - SPIRAL WITH SENSOR CABLE)
A


4.INSPECT STEERING PAD SWITCH RH


  1. Disconnect the SR1 and z9 steering pad switch RH connectors.


    E256156E02

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    SR1-1 (AU1) - z9-10 (AU1)
    Always
    Below 1 Ω
    SR1-4 (EAU) - z9-8 (EAU)
    Always
    Below 1 Ω
    SR1-2 (AU2) - z9-9 (AU2)
    Always
    Below 1 Ω


    Text in Illustration 
    *1
    Component without harness connected
    (Steering Pad Switch RH)
    -
    -



NG
REPLACE STEERING PAD SWITCH RH (Click here)
OK

REPLACE STEERING PAD SWITCH LH (Click here)