Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Malfunction in Water Temperature Warning Light

for Preparation Click here


DESCRIPTION

In this circuit, the meter ECU (meter circuit plate No.3) receives engine coolant temperature signals from the ECM using the CAN communication system (CAN No. 1 Bus). The meter ECU (meter circuit plate No.3) displays engine coolant temperature that is calculated based on the data received from the ECM.

WIRING DIAGRAM


E156127E25


INSPECTION PROCEDURE

HINT:
  1. If there is an open or short in the engine coolant temperature sensor circuit, the ECM stores the DTCs. Troubleshoot the SFI System (Click here with EGR System, Click here without EGR System).
  2. If the exhaust heat recirculation system has a malfunction, the engine coolant temperature hot warning light comes on to inform the driver of the malfunction.

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication DTC is output (Click here).

    Result:

    Result
    Proceed to
    CAN communication DTC is not output.
    A
    CAN communication DTC is output.
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.SYSTEM CHECK
  1. Check the coolant hot warning light.

    Result:

    Result
    Proceed to
    Coolant hot warning light does not come on.
    A
    Coolant hot warning light remains on.
    B



B
Go to step 4
A


3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (COOLANT HOT INDICATOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Combination Meter / Active Test.

  1. Check the operation by referring to the table below.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Coolant Hot Indicator
    Coolant hot warning light
    OFF or ON
    Confirm that the vehicle is stopped with the engine idling

    OK:
    Coolant hot warning light operation is normal.



NG
REPLACE COMBINATION METER ASSEMBLY (NO. 3 METER CIRCUIT PLATE)
OK


4.CHECK FOR DTC
  1. Check for the DTC.

    Result:

    Result
    Proceed to
    No DTC is output.
    A
    DTC P0115 is output.
    B
    DTC B1503 is output.
    C



B
GO TO SFI SYSTEM

C
GO TO METER / GAUGE SYSTEM
A


5.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMPERATURE, COOLANT TEMP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus:

    1. for Combination Meter: Body Electrical / Combination Meter / Data List.

    2. for Engine: Powertrain / Engine / Data List.

  1. Check the values by referring to the table below.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Coolant Temperature
    Engine coolant temperature/-40 to 127.5°C (-40 to 261.5°F)
    After warming up: 80 to 100°C (176 to 212°F)
    -

  1. Check the values by referring to the table below.

    Engine 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Coolant Temp
    Engine coolant temperature/Min.: -40°C (-40°F), Max.: 215°C (419°F)
    After warming up: 80 to 100°C (176 to 212°F)
    1. If -40°C (-40°F): sensor circuit open
    2. If 140°C (284°F) or more: sensor circuit shorted

    OK:
    When the Data List values of the ECUs do not match, a signal output error of the ECM is suspected.



NG
REPLACE ECM
OK


6.REPLACE COMBINATION METER ASSEMBLY (NO. 3 METER CIRCUIT PLATE)
  1. Replace the combination meter assembly (No. 3 meter circuit plate) with a new or a known good one (Click here).

    OK:
    The operation of the coolant hot warning light returns to normal.



NG
REPLACE ECM
OK

END