SEAT BELT WARNING SYSTEM > Driver Side Seat Belt Warning Light does not Operate |

| 1.READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| D Seat Buckle SW | Driver seat belt buckle switch signal/ON or OFF | ON: Driver seat belt fastened OFF: Driver seat belt not fastened | - |
|
| ||||
| OK | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Combination Meter / Active Test.
Perform the Active Test according to the display on the intelligent tester.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Driver Side Seat Belt | Driver seat belt warning light | OFF or ON | Confirm that the vehicle is stopped with the engine idling. |
|
| ||||
| OK | ||
| ||
| 3.INSPECT FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) |
![]() |
Remove the front seat inner belt assembly (driver side) (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| R5-3 (+) - R5-2 (E)*1 S22-3 (+) - S22-2 (E)*2 | Driver side seat belt unfastened | Below 1 Ω |
| R5-3 (+) - R5-2 (E)*1 S22-3 (+) - S22-2 (E)*2 | Driver side seat belt fastened | 10 kΩ or higher |
| *1 | Component without harness connected (Front Seat Inner Belt Assembly (Driver Side)) |
| *2 | for LHD |
| *3 | for RHD |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT SEAT INNER BELT ASSEMBLY RH) |
![]() |
Disconnect the 2B connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2B-14 (DBKL) - R5-3 (+)*1 2B-14 (DBKL) - S22-3 (+)*2 | Always | Below 1 Ω |
| 2B-14 (DBKL) - Body ground | Always | 10 kΩ or higher |
| R5-2 (E) - Body ground*1 S22-2 (E) - Body ground*2 | Always | Below 1 Ω |
| *1 | Front view of wire harness connector (to Instrument Panel Junction Block Assembly) |
| *2 | Front view of wire harness connector (to Front Seat Inner Belt Assembly (Driver Side)) |
| *3 | for LHD |
| *4 | for RHD |
|
| ||||
| OK | |
| 5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
Remove the instrument panel junction block assembly (Click here).

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A-18 (DBKL) - 2B-14 (DBKL) | Always | Below 1 Ω |
| 2B-14 (DBKL) - Body ground | Always | 10 kΩ or higher |
| *1 | Component without harness connected (Instrument Panel Junction Block Assembly) | *2 | Component without harness connected (Instrument Panel Junction Block Assembly) |
|
| ||||
| OK | ||
| ||
| 6.REPLACE NO. 5 METER CIRCUIT PLATE |
Replace the No. 5 meter circuit plate (Click here).
| NEXT | |
| 7.CHECK DRIVER SIDE SEAT BELT WARNING LIGHT |
Check the driver side seat belt warning light (Click here).
|
| ||||
| OK | ||
| ||
| 8.REPLACE NO. 2 METER CIRCUIT PLATE |
Replace the No. 2 meter circuit plate (Click here).
| NEXT | |
| 9.CHECK DRIVER SIDE SEAT BELT WARNING LIGHT |
Check the driver side seat belt warning light (Click here).
|
| ||||
| OK | ||
| ||