Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING

SLIDING ROOF HOUSING > INSTALLATION

for Preparation Click here



1. TEMPORARILY INSTALL REAR SLIDE ROOF PANEL SUB-ASSEMBLY
  1. Temporarily install the rear slide roof panel sub-assembly with the 16 nuts.

    NOTICE:
    1. When installing the roof panel to the vehicle, first install the roof panel center front and center rear alignment bolts to the vehicle front and rear alignment bolt installation points, as shown in the illustration.
    2. When installing the roof panel, be careful not to damage the vehicle.
    3. Perform this step with 2 or more technicians.



  1. Check that the alignment bolts are firmly installed.


    B229319E01


    Text in Illustration 
    *1
    Alignment Bolt
    *2
    Windshield Glass Moulding

    NOTICE:
    1. When the bolts are not firmly installed, water leaks and malfunctions will occur.
    2. Make sure that the lip of the windshield glass moulding is not folded down.



2. FULLY TIGHTEN REAR SLIDE ROOF PANEL SUB-ASSEMBLY


    B229320E01
  1. Fully tighten the 16 nuts to install the rear slide roof panel sub-assembly.
    Text in Illustration 
    *1
    Front Side

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    HINT:
    Tighten the nuts in the order indicated in the illustration.



3. CLEAN MOON ROOF GLASS ASSEMBLY


    BO04421E01
  1. Clean the outer edge of the moon roof glass with a non-residue solvent.

    NOTICE:
    1. Do not touch the moon roof glass surface after cleaning it.
    2. Be careful not to damage the glass.
    3. Even if using a new moon roof glass, clean the moon roof glass with a non-residue solvent.



4. INSTALL MOON ROOF GLASS ASSEMBLY


  1. Using a brush, coat the installation surface on the rear slide roof panel sub-assembly with Primer M.


    B230189E01


    Text in Illustration 
    *1
    Brush
    *2
    Primer M
    *3
    Adhesive
    -
    -

    NOTICE:
    1. Do not coat the adhesive with Primer M.
    2. Do not apply too much primer.
    3. Allow the primer to dry for 3 minutes or more.
    4. Throw away any leftover primer.

    HINT:
    If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.



  1. Using a brush or a sponge, coat the application area of the adhesive with Primer G.


    B230190E01


    Text in Illustration 
    *1
    Primer G
    Standard 
    Area
    Dimension
    a
    7.0 mm (0.276 in.)
    b
    8.0 mm (0.315 in.)
    c
    16.0 mm (0.630 in.)

    NOTICE:
    1. Do not apply too much primer.
    2. Allow the primer to dry for 3 minutes or more.
    3. Throw away any leftover primer.

    HINT:
    If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.



  1. Apply adhesive to the rear sliding roof rail sub-assembly.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or equivalent




      B214800E01
    1. Cut off the tip of the cartridge nozzle as shown in the illustration.
      Standard Dimension 
      Area
      Dimension
      a
      12.0 mm (0.472 in.)
      b
      8.0 mm (0.315 in.)

      HINT:
      After cutting off the tip, use all the adhesive within the time described in the table below.

      Usage Time Frame 
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour and 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with cartridge.



    3. Apply adhesive to the rear sliding roof rail sub-assembly as shown in the illustration.


      B230702E01


      Text in Illustration 
      *1
      Adhesive
      Standard Dimension 
      Area
      Dimension
      a
      100 mm (3.94 in.)
      b
      14.0 mm (0.551 in.)
      c
      22.0 mm (0.866 in.)
      d
      8.0 mm (0.315 in.)



  1. Install the moon roof glass assembly.



      B230195E01
    1. Position the moon roof glass assembly so that the matchmarks are aligned, and press it in gently along the rim (when glass without a clip is used).
      Text in Illustration 
      *1
      Matchmark

    2. Lightly press the moon roof glass assembly to ensure that the moon roof glass assembly is securely fit to the vehicle body (when glass without a clip is used).

      HINT:
      Press the moon roof glass assembly with a force of 98 N (10 kgf, 22.0 lbf) or more.



    3. B230186
    4. Using suction cups, engage the 2 clips to install the moon roof glass assembly.

      NOTICE:
      1. Check that the clips are attached to the vehicle body correctly.
      2. Check the clearance between the vehicle body and moon roof glass assembly.

    5. Lightly press the front surface of the moon roof glass assembly to ensure that the moon roof glass assembly is securely fit to the vehicle body.

      HINT:
      Press the moon roof glass assembly with a force of 98 N (10 kgf, 22.0 lbf) or more.



    6. Inspect the position of the moon roof glass assembly so that the measurements are within the standard values shown in the illustration.


      B230192E01

      Standard 
      Area
      Measurement
      a
      7.4 mm + 2.0 mm (0.291 in. + 0.0787 in.)
      7.4 mm - 2.0 mm (0.291 in. - 0.0787 in.)
      b
      5.0 mm + 2.0 mm (0.197 in. + 0.0787 in.)
      5.0 mm - 2.0 mm (0.197 in. - 0.0787 in.)

      HINT:
      "+" represents the condition that the glass is above the panel level. "-" represents the condition that the glass is below the panel level.

    7. Hold the moon roof glass assembly using protective tape until applied adhesive becomes hard.

      NOTICE:
      Do not drive the vehicle within the time described in the table below.

      Minimum Time:
      Temperature
      Minimum Time prior to Driving Vehicle
      35°C (95°F)
      1 hour and 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours



5. INSTALL SLIDING ROOF RAIL SUB-ASSEMBLY


  1. Install the sliding roof rail sub-assembly with the 12 nuts.


    B229317

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Engage the clamp.

  1. Connect the connector.



6. INSTALL CENTER SLIDING ROOF HOUSING MOUNTING BRACKET LH


    B229313
  1. Install the center sliding roof housing mounting bracket LH with the 2 bolts and 2 nuts.

    Torque:
    Bolt:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
    Nut:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



7. INSTALL CENTER SLIDING ROOF HOUSING MOUNTING BRACKET RH

HINT:
Use the same procedure for the RH side and LH side.



8. INSTALL FRONT SLIDING ROOF HOUSING MOUNTING BRACKET LH


    B229311
  1. Install the front sliding roof housing mounting bracket LH with the 2 bolts and 2 nuts.

    Torque:
    Bolt:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
    Nut:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



9. INSTALL FRONT SLIDING ROOF HOUSING MOUNTING BRACKET RH

HINT:
Use the same procedure for the RH side and LH side.



10. ADJUST FULLY CLOSED POSITION


    B309783E02
  1. Using a screwdriver, slide the sliding roof drive cable to align the matchmarks.
    Text in Illustration 
    *1
    Matchmark
    *a
    Rear Side

    HINT:
    Tape the screwdriver tip before use.



11. INSTALL SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY


    B229310
  1. Install the sliding roof drive gear sub-assembly with the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



12. INSTALL REAR SIDE RAIL SPACER LH


    B230208
  1. Engage the 2 clamps and install the rear side rail spacer LH



13. INSTALL REAR SIDE RAIL SPACER RH

HINT:
Use the same procedure for the RH side and LH side.



14. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY LH
  1. Check that the power switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



  1. Temporarily install the curtain shield airbag assembly with the 5 hooks.


    B228040

    NOTICE:
    Do not twist the curtain shield airbag assembly when installing it.



  1. Install the curtain shield airbag assembly to the body panel with 4 new clips and 4 new spacers.


    B228039




      C141265E04
    1. Install 4 new pins as shown in the illustration.
      Text in Illustration 
      *1
      Pin
      *2
      Clip
      *3
      Airbag
      *4
      Body
      *5
      Spacer

      NOTICE:
      Make sure that the pins of the clips are pushed in firmly.



  1. Install the 5 bolts.


    B228038

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



    B228037
  1. Connect the curtain shield airbag connector.

    NOTICE:
    When connecting any airbag connector, take care not to damage the airbag wire harness.

  1. Push in the lock to install the airbag connector.



15. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side.



16. TEMPORARILY INSTALL TILT ROOF GLASS SUB-ASSEMBLY


    B230692
  1. Using a T20 "TORX" driver, install the tilt roof glass sub-assembly with the 6 screws.



17. TEMPORARILY INSTALL SLIDING ROOF GLASS SUB-ASSEMBLY


    B229306
  1. Using a T25 "TORX" driver, install the 6 screws.



18. ADJUST SLIDING ROOF GLASS


  1. Adjust the sliding roof glass sub-assembly:


    B230193E01


    1. Adjust the position of the sliding roof glass sub-assembly so that the measurements are within the standard values shown in the illustration.
      Standard 
      Area
      Measurement
      a
      7.4 mm + 2.0 mm (0.291 in. + 0.0787 in.)
      7.4 mm - 2.0 mm (0.291 in. - 0.0787 in.)
      b
      0 + 2.0 mm (0 + 0.0787 in.)
      0 - 1.0 mm (0 - 0.0394 in.)
      c
      5.0 mm + 2.0 mm (0.197 in. + 0.0787 in.)
      5.0 mm - 2.0 mm (0.197 in. - 0.0787 in.)
      d
      1.9 mm + 1.0 mm (0.0748 in. + 0.0394 in.)
      1.9 mm - 1.0 mm (0.0748 in. - 0.0394 in.)

      HINT:
      "+" represents the condition that the glass is above the panel level. "-" represents the condition that the glass is below the panel level.

    2. After adjusting the sliding roof glass sub-assembly, using a T25 "TORX" driver, fully tighten the 6 screws to install the sliding roof glass sub-assembly.

      Torque:
      4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Adjust the tilt roof glass sub-assembly:

    1. Adjust the position of the tilt roof glass sub-assembly so that the measurements are within the standard values shown in the illustration.
      Standard 
      Area
      Measurement
      a
      7.4 mm + 2.0 mm (0.291 in. + 0.0787 in.)
      7.4 mm - 2.0 mm (0.291 in. - 0.0787 in.)
      e
      0 + 2.0 mm (0 + 0.0787 in.)
      0 - 1.0 mm (0 - 0.0394 in.)
      f
      4.0 mm + 2.0 mm (0.158 in. + 0.0787 in.)
      4.0 mm - 2.0 mm (0.158 in. - 0.0787 in.)

      HINT:
      "+" represents the condition that the glass is above the panel level. "-" represents the condition that the glass is below the panel level.

    2. After adjusting the tilt roof glass sub-assembly, using a T20 "TORX" driver, fully tighten the 6 screws to install the tilt roof glass sub-assembly.

      Torque:
      2.8 N*m{ 28 kgf*cm , 25 in.*lbf }



19. INSPECT FOR WATER LEAKS
  1. After adjusting the roof glass sub-assembly, inspect for water leaks.

  1. If there are any leaks, readjust the roof glass sub-assembly.



20. INSTALL ROOF HEADLINING ASSEMBLY

HINT:
Refer to the procedure from Install Roof Headlining Assembly (Click here).



21. INSTALL SLIDING ROOF SIDE GARNISH LH


    B230202
  1. Install the sliding roof side garnish LH.



22. INSTALL SLIDING ROOF SIDE GARNISH RH

HINT:
Use the same procedure for the RH side and LH side.



23. RESET SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY
(Click here)


24. INSPECT SLIDING ROOF SYSTEM
(Click here)