Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Check CAN Bus Line for Short to GND (RHD Models)

for Preparation Click here


DESCRIPTION

There may be a short circuit between the CAN bus main wire and GND when there is no resistance between terminals 6 (CANH) and 4 (CG) or 14 (CANL) and 4 (CG) of the DLC3.

Symptom
Trouble Area
No resistance exists between terminals 6 (CANH) and 4 (CG) or 14 (CANL) and 4 (CG) of DLC3.
  1. Short to GND in CAN bus main wire
  2. Short to GND in CAN bus branch wire
  3. Power management control ECU
  4. ECM
  5. Main body ECU
  6. Combination meter
  7. Power steering ECU
  8. Skid control ECU (Brake booster with master cylinder)
  9. Steering angle sensor
  10. Yaw rate sensor
  11. Center airbag sensor assembly
  12. Transmission control ECU
  13. Certification ECU
  14. Navigation ECU sub-assembly*1
  15. Radio and display receiver assembly*2
  16. CAN No. 1 junction connector
  17. CAN No. 2 junction connector
*1: for Navigation receiver type
*2: for Radio and display type

WIRING DIAGRAM


C253369E02


C210881E06


INSPECTION PROCEDURE

NOTICE:
  1. Turn the power switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.
  2. Turn the power switch off before inspecting CAN bus wires for a ground short.
  3. After the power switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.
  4. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the power switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
  1. Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

1.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CAN NO. 1 J/C)
  1. Turn the power switch off.



    C210276E52
  1. Disconnect the CAN No. 1 junction connector.
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to CAN No. 1 Junction Connector)
    *2
    to CAN No. 2 Junction Connector



    C210421E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    L61-6 (CANH) - L61-4 (CG)
    Power switch off
    200 Ω or higher
    L61-14 (CANL) - L61-4 (CG)
    Power switch off
    200 Ω or higher

    Text in Illustration 
    *3
    DLC3



NG
Go to step 3
OK


2.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CAN NO. 1 J/C)

C210570E18

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    Connected to
    L94-1 (CANH) - L61-4 (CG)
    Power switch off
    200 Ω or higher
    Combination meter
    L94-12 (CANL) - L61-4 (CG)
    Power switch off
    200 Ω or higher
    L94-2 (CANH) - L61-4 (CG)
    Power switch off
    200 Ω or higher
    Main body ECU
    L94-13 (CANL) - L61-4 (CG)
    Power switch off
    200 Ω or higher
    L94-4 (CANH) - L61-4 (CG)
    Power switch off
    200 Ω or higher
    Yaw rate sensor
    L94-15 (CANL) - L61-4 (CG)
    Power switch off
    200 Ω or higher
    L94-5 (CANH) - L61-4 (CG)
    Power switch off
    200 Ω or higher
    Center airbag sensor assembly
    L94-16 (CANL) - L61-4 (CG)
    Power switch off
    200 Ω or higher
    L94-6 (CANH) - L61-4 (CG)
    Power switch off
    200 Ω or higher
    Power management control ECU
    L94-17 (CANL) - L61-4 (CG)
    Power switch off
    200 Ω or higher
    L94-7 (CANH) - L61-4 (CG)
    Power switch off
    200 Ω or higher
    Transmission control ECU
    L94-18 (CANL) - L61-4 (CG)
    Power switch off
    200 Ω or higher


    Text in Illustration 
    *1
    Front view of wire harness connector
    (to CAN No. 1 Junction Connector)
    *2
    DLC3
    *3
    to Combination Meter
    *4
    to Main Body ECU
    *5
    to Yaw Rate sensor
    *6
    to Center Airbag Sensor Assembly
    *7
    to Power Management Control ECU
    *8
    to Transmission Control ECU

Result:
Result
Proceed to
OK
A
NG (to ECU or sensor wire)
B



B
Go to step 4
A

REPLACE CAN NO. 1 JUNCTION CONNECTOR 

3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CAN NO. 2 J/C)


  1. Disconnect the CAN No. 2 junction connector.


    C210570E19


    Text in Illustration 
    *1
    Front view of wire harness connector
    (to CAN No. 2 Junction Connector)
    *2
    DLC3
    *3
    to Steering Angle Sensor
    *4
    to Power Steering ECU
    *5
    to Skid Control ECU
    *6
    to DLC3
    *7
    1. to Navigation ECU Sub-assembly*1
    2. to Radio and Display Receiver Assembly*2
    *8
    to CAN No. 1 Junction Connector
    *9
    to Certification ECU
    *10
    to ECM

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    Connected to
    L95-1 (CANH) - L61-4 (CG)
    Power switch off
    200 Ω or higher
    Steering angle sensor
    L95-12 (CANL) - L61-4 (CG)
    Power switch off
    200 Ω or higher
    L95-2 (CANH) - L61-4 (CG)
    Power switch off
    200 Ω or higher
    Power steering ECU
    L95-13 (CANL) - L61-4 (CG)
    Power switch off
    200 Ω or higher
    L95-3 (CANH) - L61-4 (CG)
    Power switch off
    200 Ω or higher
    Skid control ECU
    L95-14 (CANL) - L61-4 (CG)
    Power switch off
    200 Ω or higher
    L95-4 (CANH) - L61-4 (CG)
    Power switch off
    200 Ω or higher
    DLC3
    L95-15 (CANL) - L61-4 (CG)
    Power switch off
    200 Ω or higher
    L95-5 (CANH) - L61-4 (CG)
    Power switch off
    200 Ω or higher
    1. Navigation ECU sub-assembly*1
    2. Radio and display receiver assembly*2
    L95-16 (CANL) - L61-4 (CG)
    Power switch off
    200 Ω or higher
    L95-6 (CANH) - L61-4 (CG)
    Power switch off
    200 Ω or higher
    CAN No. 1 junction connector
    L95-17 (CANL) - L61-4 (CG)
    Power switch off
    200 Ω or higher
    L95-7 (CANH) - L61-4 (CG)
    Power switch off
    200 Ω or higher
    Certification ECU
    L95-18 (CANL) - L61-4 (CG)
    Power switch off
    200 Ω or higher
    L95-9 (CANH) - L61-4 (CG)
    Power switch off
    200 Ω or higher
    ECM
    L95-20 (CANL) - L61-4 (CG)
    Power switch off
    200 Ω or higher

    *1: for Navigation receiver type
    *2: for Radio and display type

Result:
Result
Proceed to
OK
A
NG (to DLC3 branch wire)
B
NG (to CAN No. 1 J/C main wire)
C
NG (to ECU or sensor wire)
D



B
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3

C
REPAIR CAN BUS MAIN WIRE OR CONNECTOR (CAN NO. 1 J/C - CAN NO. 2 J/C)

D
Go to step 4
A

REPLACE CAN NO. 2 JUNCTION CONNECTOR 

4.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
  1. Reconnect the CAN No. 1 junction connector and CAN No. 2 junction connector wire harness connector.

  1. Disconnect the ECU or sensor connected to the CAN bus wire that is shorted to ground.

    HINT:
    If the ECU or sensor has multiple connectors, disconnect the connector that includes the CAN bus wires. To determine the ECU or sensor that is connected to the shorted bus wire, refer to the terminals of ECU tables (Click here).



    C210421E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    L61-6 (CANH) - L61-4 (CG)
    Power switch off
    200 Ω or higher
    L61-14 (CANL) - L61-4 (CG)
    Power switch off
    200 Ω or higher

    HINT:
    If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).

    Text in Illustration 
    *1
    DLC3



NG
REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH WIRE OR CONNECTOR
OK

REPLACE CORRESPONDING ECU OR SENSOR