Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM

THEFT DETERRENT SYSTEM > Engine Hood Courtesy Switch Circuit

for Preparation Click here


DESCRIPTION

The engine hood courtesy switch is installed together with the hood lock. This switch turns on when the engine hood is closed and turns off when the engine hood is opened.

WIRING DIAGRAM


B219532E02


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Select the item below in the Data List and read the display on the intelligent tester.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Hood Courtesy SW
    Engine hood courtesy switch signal/ON or OFF
    ON: Engine hood open
    OFF: Engine hood closed
    -

    OK:
    The indicator on the intelligent tester switches between ON and OFF in accordance with the engine hood courtesy switch status.



NG
Go to step 2
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


  1. Disconnect the 2C instrument panel junction block assembly and A main body ECU (multiplex network body ECU) connectors.


    B220554E03

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2C-38 - A-20 (HCTY)
    Always
    Below 1 Ω


    Text in Illustration 
    *1
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    *2
    Front view of wire harness connector
    (to Main Body ECU (Multiplex Network Body ECU))



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK


3.CHECK HARNESS AND CONNECTOR (ENGINE HOOD COURTESY SWITCH - BODY GROUND)


    B229082E01
  1. Disconnect the A47 engine hood courtesy switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A47-2 - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Hood Lock Assembly (Engine Hood Courtesy Switch))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (ENGINE HOOD COURTESY SWITCH - MAIN BODY ECU)


    B229084E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A47-1 - 2C-38
    Always
    Below 1 Ω
    A47-1 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Hood Lock Assembly (Engine Hood Courtesy Switch))
    *2
    Front view of wire harness connector
    (to Instrument Panel Junction Block Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT HOOD LOCK ASSEMBLY (ENGINE HOOD COURTESY SWITCH)


    B229081E01
  1. Remove the hood lock assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A47-1 - A47-2
    Locked
    Below 1 Ω
    Unlocked
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (Hood Lock Assembly (Engine Hood Courtesy Switch))
    *2
    Unlock
    *3
    Lock



NG
REPLACE HOOD LOCK ASSEMBLY (ENGINE HOOD COURTESY SWITCH) (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)