Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM

THEFT DETERRENT SYSTEM > Security Indicator Light Circuit

for Preparation Click here


DESCRIPTION

Even when the theft deterrent system is in the disarmed state, the security indicator light blinks due to a signal output from the immobiliser system. The security indicator light blinks continuously due to a continuous signal received from the immobiliser system while in the armed state.
The main body ECU (multiplex network body ECU) causes the security indicator light to come on only during the arming preparation and alarm sounding states.

WIRING DIAGRAM


B216738E03


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Select the item below in the Active Test and then check that the indicator operates.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Security Indicator
    Security indicator
    ON / OFF
    -

    OK:
    The security indicator light flashes and goes off correctly when operated through the intelligent tester.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


  1. Disconnect the 2A instrument panel junction block assembly and A main body ECU (multiplex network body ECU) connectors.


    B229089E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2A-51 - A-25 (IND)
    Always
    Below 1 Ω


    Text in Illustration 
    *1
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    *2
    Front view of wire harness connector
    (to Main Body ECU (Multiplex Network Body ECU))



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK


3.CHECK HARNESS AND CONNECTOR (COMBINATION METER (SECURITY INDICATOR) - MAIN BODY ECU)


    B229088E01
  1. Disconnect the L27 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2A-51 - L27-22 (LP)
    Always
    Below 1 Ω
    L27-22 (LP) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Combination Meter Assembly (Security Indicator Light))
    *2
    Front view of wire harness connector
    (to Instrument Panel Junction Block Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (COMBINATION METER (SECURITY INDICATOR LIGHT) - BODY GROUND)


    B229090E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L27-30 (ES) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Combination Meter Assembly (Security Indicator Light))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT SECURITY INDICATOR LIGHT


    B229091E01
  1. Remove the combination meter assembly with harness connected. (Click here)

  1. Apply battery voltage from the wire harness back side between the specified terminals of the security indicator light, and check the lighting condition of the security indicator light.

    Standard :
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal L27-22 (LP)
    Battery negative (-) → Terminal L27-30 (ES)
    Security indicator light comes on

    Text in Illustration 
    *1
    Component with harness connected
    (Combination Meter Assembly (Security Indicator Light))

    NOTICE:
    1. If the positive (+) lead and negative (-) lead are incorrectly connected, the security indicator light will not come on.
    2. Voltage of more than 12 V will damage the security indicator.
    3. If the voltage is too low, the security indicator light will not come on.



NG
REPLACE NO.3 METER CIRCUIT PLATE (SECURITY INDICATOR LIGHT) (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)