Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM

THEFT DETERRENT SYSTEM > Intrusion Sensor Cancel Switch Circuit

for Preparation Click here


DESCRIPTION

  1. When the intrusion sensor cancel switch on the map light assembly is pressed, the sensor off signal is sent to the main body ECU (multiplex network body ECU) which causes the intrusion sensor to stop operating.

WIRING DIAGRAM


B229043E01


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (INTRUSION SENSOR CANCEL SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Select the item below in the Data List and read the display on the intelligent tester.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Intrusion Sens OFF SW
    Intrusion sensor cancel switch/ON or OFF
    ON: Intrusion sensor cancel switch on
    OFF: Intrusion sensor cancel switch off
    -

    OK:
    The indicator on the intelligent tester switches between ON and OFF in accordance with the intrusion sensor cancel switch status.



NG
Go to step 2
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MAP LIGHT ASSEMBLY)
  1. Disconnect the L8 main body ECU (multiplex network body ECU) and U3*4 or U13*5 map light assembly connectors.


B229083E05

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L8-8 (SSW1) - U3-7 (SOFF)*4
    L8-8 (SSW1) - U13-1 (SOFF)*5
    Always
    Below 1 Ω
    U3-1 (GND1) - Body ground*4
    U13-9 (GND1) - Body ground*5
    Always
    Below 1 Ω
    L8-8 (SSW1) - Body ground
    Always
    10 kΩ or higher

    1. *4: w/o Sliding Roof System
    2. *5: w/ Sliding Roof System

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Main Body ECU (Multiplex Network Body ECU))
    *2
    Front view of wire harness connector
    (to Map Light Assembly (Intrusion Sensor))
    *3
    Front view of wire harness connector
    (to Map Light Assembly (Intrusion Sensor))
    *4
    w/o Sliding Roof System
    *5
    w/ Sliding Roof System
    -
    -



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT MAP LIGHT ASSEMBLY (INTRUSION SENSOR CANCEL SWITCH)


    B234882E01
  1. Remove the map light assembly (intrusion sensor cancel switch) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    U3-7 (SOFF) - U3-1 (GND1)*3
    U13-1 (SOFF) - U13-9 (GND1)*4
    Intrusion sensor ON (intrusion sensor cancel switch not pressed)
    10 kΩ or higher
    U3-7 (SOFF) - U3-1 (GND1)*3
    U13-1 (SOFF) - U13-9 (GND1)*4
    Intrusion sensor off (intrusion sensor cancel switch pressed)
    Below 1 Ω

    1. *3: w/o Sliding Roof System
    2. *4: w/ Sliding Roof System
    Text in Illustration 
    *1
    Component without harness connected
    (Map Light Assembly (Intrusion Sensor Cancel Switch))
    *2
    Component without harness connected
    (Map Light Assembly (Intrusion Sensor Cancel Switch))
    *3
    w/o Sliding Roof System
    *4
    w/ Sliding Roof System



NG
REPLACE MAP LIGHT ASSEMBLY (INTRUSION SENSOR CANCEL SWITCH) (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)