Home › Drivetrain › P410 HYBRID TRANSMISSION / TRANSAXLE › ELECTRONIC SHIFT LEVER SYSTEM

DTC    C2300    Actuator System Malfunction

for Preparation Click here


DESCRIPTION

The shift control actuator consists of the parking lock motor and the rotation angle sensor. The transmission control ECU receives a P position switch signal from the power management control ECU (HV CPU) and activates the parking lock motor by controlling current, causing the parking lock mechanism to switch. The transmission control ECU also detects the rotor rotation angle through the rotation angle sensor to control timing of current application to the coils. The transmission control ECU outputs this DTC when it detects a malfunction in the shift control actuator system.

DTC No.
DTC Detection Condition
Trouble Area
C2300
Open or short in the P CON MTR relay (transaxle parking lock control relay) or shift control actuator assembly (parking lock motor or rotation angle sensor), or internal malfunction of the shift control actuator assembly (parking lock motor or rotation angle sensor).
  1. Transmission control ECU assembly
  2. Auxiliary battery
  3. Shift control actuator assembly
  4. Hybrid vehicle transaxle assembly
  5. Wire harness or connector

WIRING DIAGRAM


C225844E03


INSPECTION PROCEDURE

NOTICE:
It is not possible to clear the following DTCs using the intelligent tester: DTCs C2300 (Actuator System Malfunction), C2301 (Shift Changing Time Malfunction), C2303 (Short in Power Source Relay Circuit), C2304 (Open or Short Circuit in U Phase), C2305 (Open or Short Circuit in V Phase), C2306 (Open or Short Circuit in W Phase), C2307 (Power Supply) and C2309 (Open in B+ Circuit). After the repair, it is necessary to disconnect the P CON MAIN fuse and wait for at least 60 seconds to clear the DTCs.

1.CHECK FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Chassis / Transmission Control / Trouble Codes.

  1. Read the freeze frame data "Current flag record" of C2300.

    Result:
    Result
    Proceed to
    OFF
    A
    ON
    B

  1. Turn the power switch off.



B
REPLACE TRANSMISSION CONTROL ECU ASSEMBLY (Click here)
A


2.CHECK DTC OUTPUT (TRANSMISSION CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Chassis / Transmission Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    Any of the following DTCs are not output.
    A
    Any of the following DTCs are output.
    B

    DTC No.
    Relevant Diagnosis
    C2304
    Open or Short Circuit in U Phase
    C2305
    Open or Short Circuit in V Phase
    C2306
    Open or Short Circuit in W Phase

  1. Turn the power switch off.



B
GO TO DTC CHART (Click here)
A


3.CHECK FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Chassis / Transmission Control / Trouble Codes.

  1. Read the freeze frame data of C2300.

    Result:
    Result
    Proceed to
    IG (+B) voltage is 9 V or more
    A
    IG (+B) voltage is less than 9 V
    B

  1. Turn the power switch off.



B
REPLACE AUXILIARY BATTERY (Click here)
A


4.CLEAR DTC
  1. Turn the power switch on (IG).

  1. Enter the following menus: Chassis / Transmission Control / Trouble Codes.

  1. Read and record the DTCs and freeze frame data.

  1. Turn the power switch off.

  1. Disconnect the P CON MAIN fuse and wait for at least 60 seconds.

  1. Check for DTCs again to see if the DTCs are cleared.


NEXT


5.CHARGE AUXILIARY BATTERY
  1. Charge the auxiliary battery.


NEXT


6.CHECK DTC OUTPUT (SIMULATION TEST)
  1. Connect the intelligent tester to the DLC3.

  1. Release the brake pedal and turn the power switch on (IG).

    HINT:
    Do not turn the power switch on (READY).

  1. Depress the brake pedal and move the selector lever to N.

  1. Enter the following menus: Chassis / Transmission Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    C2300 is output
    A
    DTC is not output.
    B

  1. Turn the power switch off.



B
END (AUXILIARY BATTERY WAS INSUFFICIENTLY CHARGED)
A


7.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU ASSEMBLY - SHIFT CONTROL ACTUATOR)
  1. Disconnect the A23 transmission control ECU assembly connector.

  1. Disconnect the D2 shift control actuator assembly connector.



    C210299E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    A23-7 (VC) - D2-9 (RVC)
    Power switch off
    Below 1 Ω
    A23-17 (RA) - D2-3 (RA)
    Power switch off
    Below 1 Ω
    A23-8 (RB) - D2-5 (RB)
    Power switch off
    Below 1 Ω
    A23-19 (E2) - D2-8 (RE2)
    Power switch off
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    A23-7 (VC) or D2-9 (RVC) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    A23-17 (RA) or D2-3 (RA) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    A23-8 (RB) or D2-5 (RB) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    A23-19 (E2) or D2-8 (RE2) - Body ground and other terminals
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Transmission Control ECU Assembly)
    *2
    Front view of wire harness connector
    (to Shift Control Actuator Assembly)

  1. Connect the shift control actuator assembly connector.

  1. Connect the transmission control ECU assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK SHIFT CONTROL ACTUATOR ASSEMBLY (ROTATION ANGLE SENSOR)
  1. Disconnect the A23 transmission control ECU assembly connector.



    C208986E15
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A23-7 (VC) - A23-17 (RA)
    Power switch off
    10 kΩ or higher
    A23-7 (VC) - A23-8 (RB)
    Power switch off
    10 kΩ or higher
    A23-7 (VC) - A23-19 (E2)
    Power switch off
    520 to 600 Ω
    A23-17 (RA) - A23-8 (RB)
    Power switch off
    10 kΩ or higher
    A23-17 (RA) - A23-19 (E2)
    Power switch off
    10 kΩ or higher
    A23-8 (RB) - A23-19 (E2)
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Transmission Control ECU Assembly)

  1. Connect the transmission control ECU assembly connector.



NG
REPLACE SHIFT CONTROL ACTUATOR ASSEMBLY (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU ASSEMBLY - BODY GROUND)
  1. Disconnect the A24 transmission control ECU assembly connector.



    C208987E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    A24-6 (E01) - Body ground
    Power switch off
    Below 1 Ω
    A24-5 (E02) - Body ground
    Power switch off
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Transmission Control ECU Assembly)

  1. Connect the transmission control ECU assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.CHECK SHIFT CONTROL ACTUATOR ASSEMBLY
  1. Disconnect the shift control actuator assembly connector.

  1. Remove the shift control actuator 3 bolts (Click here).

  1. Slightly pull the shift control actuator assembly from the hybrid vehicle transaxle.



    C211667
  1. Using a screwdriver with its tip wrapped with protective tape or a piece of cloth, rotate the shaft.

    OK:
    The shift control actuator assembly turns smoothly.

    NOTICE:
    1. During this inspection, make sure to use a screwdriver with its tip wrapped with protective tape or a piece of cloth to prevent the splines of the actuator from being damaged.
    2. The shift control actuator cannot be disassembled.



NG
REPLACE SHIFT CONTROL ACTUATOR ASSEMBLY (Click here)
OK


11.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY


    C211914E01
  1. Wrap the shaft with a piece of cloth and turn it using pliers.

    OK:
    The shaft rotates smoothly in the lock and unlock directions.

    NOTICE:
    1. Rotates the shaft using torque within 4 to 7 N*m (41 to 71 kgf*cm, 36 to 61 in.*lbf).
    2. During this inspection, ensure to use a piece of cloth to prevent the shaft splines from being damaged.

    Text in Illustration 
    *1
    Lock
    *2
    Unlock
    *3
    Rotate approximately 20°.

  1. Set the shaft in the lock position after the inspection.



NG
REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY (Click here)
OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY (Click here)