POWER MIRROR CONTROL SYSTEM > Mirror Heater does not Operate with Rear Defogger Switch |

| 1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body /Air Conditioner / Active Test.
Perform an Active Test according to the display on the intelligent tester.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Mirror Heater Relay | Mirror heater | ON / OFF | - |
| Result | Proceed to |
| Mirror heater operation on both mirrors is not normal | A |
| Mirror heater operation on RH side mirror is not normal | B |
| Mirror heater operation on LH side mirror is not normal | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK DEFOGGER SYSTEM |
Check the rear window defogger operation.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - BODY GROUND) |
![]() |
Disconnect the integration relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1H-3 (GND2) - Body ground | Always | Below 1 Ω |
| 1G-22 (GND1) - Body ground | Always | Below 1 Ω |
| *1 | Front view of wire harness connector (to Integration Relay) |
| *2 | Front view of wire harness connector (to Integration Relay) |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - INTEGRATION RELAY) |
![]() |
Disconnect the integration relay connector.
Disconnect the outer rear view mirror assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1I-2 (MHTR) - N4-2 (HR+) | Always | Below 1 Ω |
| 1I-2 (MHTR) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Outer Rear View Mirror Assembly RH) |
| *2 | Front view of wire harness connector (to Integration Relay) |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - INTEGRATION RELAY) |
![]() |
Disconnect the integration relay connector.
Disconnect the outer rear view mirror assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1I-2 (MHTR) - O4-2 (HL+) | Always | Below 1 Ω |
| 1I-2 (MHTR) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Outer Rear View Mirror Assembly LH) |
| *2 | Front view of wire harness connector (to Integration Relay) |
|
| ||||
| OK | |
| 6.REPLACE INTEGRATION NO.1 RELAY |
Replace the integration relay (Click here).
| OK | |
| 7.CHECK REAR WINDOW DEFOGGER AND MIRROR HEATER |
Check the mirror heater system.
|
| ||||
| OK | ||
| ||
| 8.CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH |
![]() |
Remove the outer rear view mirror assembly RH (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| N4-2 (HR+) - N4-1 (HR-) | 25°C (77°F) | 7.6 to 11.4 Ω |
| *1 | Component without harness connected (Outer Rear View Mirror Assembly RH) |
|
| ||||
| OK | ||
| ||
| 9.CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH |
![]() |
Remove the outer rear view mirror assembly LH (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O4-2 (HL+) - O4-1 (HL-) | 25°C (77°F) | 7.6 to 11.4 Ω |
| *1 | Component without harness connected (Outer Rear View Mirror Assembly LH) |
|
| ||||
| OK | ||
| ||