AIRBAG SYSTEM > Trouble in Passenger Airbag ON/OFF Indicator |
| Airbag Cut Off Switch | Passenger Airbag ON/OFF Indicator | SRS Warning Light | |
| ON Indicator | OFF Indicator | ||
| ON position | ON | OFF | OFF |
| OFF position | OFF | ON | OFF |
| Switch failure | OFF | ON | ON |

| 1.CHECK SRS WARNING LIGHT |
Turn the power switch on (IG), and check the SRS warning light condition.
|
| ||||
| OK | |
| 2.CHECK CONNECTORS |
Turn the power switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connectors are properly connected to the center airbag sensor assembly and airbag cut off switch.
Disconnect the connectors from the center airbag sensor assembly and airbag cut off switch.
Check that the terminals of the connectors are not damaged.
Check that the short spring for the instrument panel wire connector with the activation prevention mechanism is not deformed or damaged.
|
| ||||
| OK | |
| 3.CHECK INSTRUMENT PANEL WIRE (OPEN) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L117-2 (PMC+) - L117-1 (PMC-) | Always | Below 1 Ω |
| *1 | Airbag Cut Off Switch |
| *2 | Center Airbag Sensor Assembly |
| *3 | Instrument Panel Wire |
| *4 | Front view of wire harness connector (to Center Airbag Sensor Assembly) |
| *5 | Connector B |
| *6 | Front view of wire harness connector (to Airbag Cut Off Switch) |
| *7 | Connector C |
|
| ||||
| OK | |
| 4.CHECK INSTRUMENT PANEL WIRE (SHORT) |
![]() |
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L117-2 (PMC+) - L117-1 (PMC-) | Always | 1 MΩ or higher |
| *1 | Airbag Cut Off Switch |
| *2 | Center Airbag Sensor Assembly |
| *3 | Instrument Panel Wire |
| *4 | Front view of wire harness connector (to Airbag Cut Off Switch) |
| *5 | Connector C |
|
| ||||
| OK | |
| 5.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L117-2 (PMC+) - Body ground | Power switch on (IG) | Below 1 V |
| L117-1 (PMC-) - Body ground | Power switch on (IG) | Below 1 V |
| *1 | Airbag Cut Off Switch |
| *2 | Center Airbag Sensor Assembly |
| *3 | Instrument Panel Wire |
| *4 | Front view of wire harness connector (to Airbag Cut Off Switch) |
| *5 | Connector C |
|
| ||||
| OK | |
| 6.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+) |
![]() |
Turn the power switch off.
Disconnect the cable from the negative (-) battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L117-2 (PMC+) - Body ground | Always | 1 MΩ or higher |
| L117-1 (PMC-) - Body ground | Always | 1 MΩ or higher |
| *1 | Airbag Cut Off Switch |
| *2 | Center Airbag Sensor Assembly |
| *3 | Instrument Panel Wire |
| *4 | Front view of wire harness connector (to Airbag Cut Off Switch) |
| *5 | Connector C |
|
| ||||
| OK | |
| 7.CHECK AIRBAG CUT OFF SWITCH |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L117-2 (PMC+) - L117-1 (PMC-) | Cut off switch in ON | 360 to 440 Ω |
| L117-2 (PMC+) - L117-1 (PMC-) | Cut off switch in OFF | 90 to 110 Ω |
| *1 | Component without harness connected (Airbag Cut Off Switch) |
|
| ||||
| OK | ||
| ||