Home › Vehicle Exterior › WINDOW / GLASS › WINDOW DEFOGGER SYSTEM

WINDOW DEFOGGER SYSTEM > Rear Window Defogger System does not Operate

for Preparation Click here


DESCRIPTION

When the rear window defogger switch on the air conditioning control panel assembly is pressed, the operation signal is transmitted to the air conditioning amplifier assembly through a LIN communication line. When the air conditioning amplifier assembly receives the signal, it turns on the integration relay to operate the rear window defogger.

WIRING DIAGRAM


B231920E02


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK REAR WINDOW DEFOGGER SYSTEM
  1. Activate the rear defogger system and check the symptoms.

    Result:
    Result
    Proceed to
    Both back window defoggers do not warm up.
    A
    The back door glass defogger does not warm up.
    B
    The back window fix glass defogger does not warm up.
    C



B
Go to step 8

C
Go to step 9
A


2.CHECK POWER STEERING SYSTEM (Battery Voltage Lo Record)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / EMPS / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    EMPS 
    Tester Display
    Measurement item/Range
    Normal Condition
    Diagnostic Note
    Battery Voltage Lo Record
    Battery voltage reduction history/ Min.: 0 times, Max.: 65535 times
    0 to 65535
    -

    Result:
    Result
    Proceed to
    No control history is stored.
    A
    Control history is stored.
    B



B
GO TO CHARGING SYSTEM (Click here)
A


3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DEFOGGER RELAY)
  1. Enter the following menus: Body / Air Conditioner / Active Test.

  1. Perform the Active Test according to the display on the intelligent tester.

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Defogger Relay (Rear)
    Rear window defogger
    ON/OFF
    -

    OK:
    The window defogger system operates normally.



NG
Go to step 4
OK

GO TO AIR CONDITIONING SYSTEM (Click here)  

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - INTEGRATION RELAY)


    B225725E01
  1. Disconnect the 1G integration relay connector.

  1. Disconnect the L17 air conditioning amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L17-20 (RDEF) - 1G-15 (DEF)
    Always
    Below 1 Ω
    1G-15 (DEF) - Body ground
    Always
    10 kΩ or higher
    L17-14 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Air Conditioning Amplifier Assembly)
    *2
    Front view of wire harness connector
    (to Integration Relay)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


    B202140E10
  1. Turn the power switch on (READY).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L17-20 (RDEF) - L17-14 (GND)
    Rear defogger switch off
    11 to 14 V
    L17-20 (RDEF) - L17-14 (GND)
    Rear defogger switch on
    Below 1 V

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to Air Conditioning Amplifier Assembly)



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK


6.INSPECT RADIO SETTING CONDENSER


    E183893E03
  1. Remove the radio setting condenser.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    10 kΩ or higher
    2 - 3
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Radio Setting Condenser



NG
REPLACE RADIO SETTING CONDENSER
OK


7.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - BODY GROUND)


    B225723E03
  1. Disconnect the V1 back door glass battery side connector.

  1. Disconnect the V2 back window fix glass battery side connector.

  1. Disconnect the 1I integration relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1I-1 (RDEF) - Body ground
    Always
    10 kΩ or higher
    1I-1 (RDEF) - V1-1
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Integration Relay)
    *2
    Front view of wire harness connector
    (to Back Door Glass)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INTEGRATION NO.1 RELAY (Click here)  

8.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - BACK DOOR GLASS)


    B233203E02
  1. Disconnect the V1 back door glass battery side connector.

  1. Disconnect the V10 back door glass body ground side connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1I-1 (RDEF) - V1-1
    Always
    Below 1 Ω
    V10-1 - Body ground
    Always
    Below 1 Ω
    1I-1 (RDEF) - Body ground
    Always
    10 kΩ or higher
    V1-1 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Integration Relay)
    *2
    Front view of wire harness connector
    (to Back Door Glass)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BACK DOOR GLASS  

9.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - BACK WINDOW FIX GLASS)


    B233204E01
  1. Disconnect the V2 back window fix glass battery side connector.

  1. Disconnect the V8 back window fix glass body ground side connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1I-1 (RDEF) - V2-1
    Always
    Below 1 Ω
    V8-1 - Body ground
    Always
    Below 1 Ω
    1I-1 (RDEF) - Body ground
    Always
    10 kΩ or higher
    V2-1 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Integration Relay)
    *2
    Front view of wire harness connector
    (to Back Window Fix Glass)
    *3
    Back Window Fix Glass Battery Side
    *4
    Back Window Fix Glass Body Ground Side



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BACK WINDOW FIX GLASS