DTC C1627 Vehicle Height Sensor Voltage is Low or High |
| DTC No. | DTC Detection Condition | Trouble Area |
| C1627 |
|
|
| for LED Headlight |

| for Halogen Headlight |

| 1.CHECK DTC OUTPUT |
Clear the DTCs (Click here).
Check for DTCs (Click here).
| Result | Proceed to |
| DTC C1627 is output | A |
| DTCs are not output | B |
|
| ||||
| A | |
| 2.CHECK VEHICLE SPECIFICATION |
Check vehicle specifications.
| Result | Proceed to |
| for LED Headlight | A |
| for Halogen Headlight | B |
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - PARKING ASSIST ECU) |
Disconnect the A48 connector from the headlight leveling ECU assembly.
Disconnect the L151 connector from the parking assist ECU.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A48-12 (SBR) - Body ground | Always | 10 kΩ or higher |
| A48-21 (SGR) - Body ground | Always | 10 kΩ or higher |
| A48-12 (SBR) - L151-28 (HB+) | Always | Below 1 Ω |
| A48-21 (SGR) - L151-29 (HGND) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 4.CHECK HEADLIGHT LEVELING ECU ASSEMBLY |
Reconnect the A48 connector to the headlight leveling ECU assembly.
Disconnect the L151 connector from the parking assist ECU.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L151-28 (HB+) - L151-29 (HGND) | Power switch on (IG) | 4.75 to 5.25 V |
| *a | Front view of wire harness connector (to Parking Assist ECU) |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH - PARKING ASSIST ECU) |
Disconnect the L151 connector from the parking assist ECU.
Disconnect the S3 connector from the rear height control sensor sub-assembly RH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L151-27 (HBL+) - Body ground | Always | 10 kΩ or higher |
| L151-31 (HG1) - Body ground | Always | 10 kΩ or higher |
| L151-27 (HBL+) - S3-3 (SHB) | Always | Below 1 Ω |
| L151-31 (HG1) - S3-1 (SHG) | Always | Below 1 Ω |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH - PARKING ASSIST ECU) |
Disconnect the L151 connector from the parking assist ECU.
Disconnect the S3 connector from the rear height control sensor sub-assembly RH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L151-30 (HBE+) - Body ground | Always | 10 kΩ or higher |
| L151-31 (HG1) - Body ground | Always | 10 kΩ or higher |
| L151-30 (HBE+) - S3-3 (SHB) | Always | Below 1 Ω |
| L151-31 (HG1) - S3-1 (SHG) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 7.CHECK REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH |
Reconnect the L151 connector to the parking assist ECU.
Disconnect the S3 connector from the rear height control sensor sub-assembly RH.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S3-3 (SHB) - S3-1 (SHG) | Power switch on (IG) | 4.75 to 5.25 V |
| *a | Front view of wire harness connector (to Rear Height Control Sensor Sub-assembly RH) |
|
| ||||
| OK | ||
| ||