Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTELLIGENT PARKING ASSIST SYSTEM

DTC    C1628    Vehicle Height Sensor Failure

for Preparation Click here


DESCRIPTION

The rear height control sensor sub-assembly RH is connected to the parking assist ECU. This DTC is stored when the parking assist ECU judges that vehicle height sensor signal received from the rear height control sensor sub-assembly RH is abnormal or has not changed (rear height control sensor sub-assembly RH seized).

DTC No.
DTC Detection Condition
Trouble Area
C1628
  1. Height control sensor signal is abnormal
  2. Height control sensor seized
  1. Harness or connector
  2. Rear height control sensor sub-assembly RH
  3. Parking assist ECU

WIRING DIAGRAM


E236872E02


INSPECTION PROCEDURE

NOTICE:
  1. When the "System initializing" message is displayed on the navigation ECU sub-assembly after the auxiliary battery cable has been disconnected, correct the steering angle neutral point (Click here).
  2. Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the intelligent parking assist system may be needed (Click here).

1.CHECK VEHICLE SPECIFICATION
  1. Check vehicle specification.

    Result:
    Result
    Proceed to
    for LED Headlight
    A
    for Halogen Headlight
    B



B
Go to step 3
A


2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY)
  1. Disconnect the L151 connector from the parking assist ECU.

  1. Disconnect the S3 connector from the rear height control sensor sub-assembly RH.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L151-27 (HBL+) - Body ground
    Always
    10 kΩ or higher
    L151-9 (HI1) - Body ground
    Always
    10 kΩ or higher
    L151-31 (HG1) - Body ground
    Always
    10 kΩ or higher
    L151-27 (HBL+) - S3-3 (SHB)
    Always
    Below 1 Ω
    L151-9 (HI1) - S3-2 (SHRR)
    Always
    Below 1 Ω
    L151-31 (HG1) - S3-1 (SHG)
    Always
    Below 1 Ω

    Result:
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 4
A

REPAIR OR REPLACE HARNESS OR CONNECTOR 

3.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY)
  1. Disconnect the L151 connector from the parking assist ECU.

  1. Disconnect the S3 connector from the rear height control sensor sub-assembly RH.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L151-30 (HBE+) - Body ground
    Always
    10 kΩ or higher
    L151-9 (HI1) - Body ground
    Always
    10 kΩ or higher
    L151-31 (HG1) - Body ground
    Always
    10 kΩ or higher
    L151-30 (HBE+) - S3-3 (SHB)
    Always
    Below 1 Ω
    L151-9 (HI1) - S3-2 (SHRR)
    Always
    Below 1 Ω
    L151-31 (HG1) - S3-1 (SHG)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH
  1. Reconnect the L151 connector to the parking assist ECU.

  1. Disconnect the S3 connector from the rear height control sensor sub-assembly RH.



    E228130E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    S3-3 (SHB) - S3-1 (SHG)
    Power switch on (IG)
    4.75 to 5.25 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Rear Height Control Sensor Sub-assembly RH)



NG
REPLACE PARKING ASSIST ECU (Click here)
OK

REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH (Click here)