Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM (w/o EGR System)

SFI SYSTEM (w/o EGR System) > ECM Power Source Circuit

for Preparation Click here


DESCRIPTION

When the power switch is turned on (IG), auxiliary battery voltage is applied to IGSW of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the coil, closing the contacts of the No. 2 integration relay (EFI MAIN relay) and supplying power to either terminal +B and +B2 of the ECM.

WIRING DIAGRAM


A231565E09


INSPECTION PROCEDURE

NOTICE:
  1. After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    D28-104 (E1) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - BODY GROUND)
OK


2.CHECK TERMINAL VOLTAGE (IGSW VOLTAGE)


    A194151E36
  1. Disconnect the ECM connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A57-28 (IGSW) - Body ground
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the ECM connector.



NG
Go to step 7
OK


3.INSPECT NO. 2 INTEGRATION RELAY (EFI MAIN RELAY)
  1. Inspect the No. 2 integration relay (EFI MAIN relay) (Click here).



NG
REPLACE NO. 2 INTEGRATION RELAY (EFI MAIN RELAY) (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY (EFI MAIN RELAY) - ECM)
  1. Remove the No. 2 integration relay from the engine room relay block and junction block assembly.

  1. Disconnect the No. 2 integration relay connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    1B-4 - A57-1 (+B2)
    Always
    Below 1 Ω
    1B-4 - A57-2 (+B)
    Always
    Below 1 Ω
    1B-2 - A57-6 (MREL)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    1B-4 or A57-1 (+B2) - Body ground
    Always
    10 kΩ or higher
    1B-4 or A57-2 (+B) - Body ground
    Always
    10 kΩ or higher
    1B-2 or A57-6 (MREL) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the No. 2 integration relay connector.

  1. Reinstall the No. 2 integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 2 INTEGRATION RELAY (EFI MAIN RELAY) - ECM)
OK


5.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY (EFI MAIN RELAY) - AUXILIARY BATTERY)
  1. Remove the No. 2 integration relay from the engine room relay block and junction block assembly.

  1. Disconnect the No. 2 integration relay connector.

  1. Disconnect the negative (-) auxiliary battery terminal.

  1. Disconnect the positive (+) auxiliary battery terminal.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    1C-1 - Positive (+) auxiliary battery terminal
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    1C-1 or Positive (+) auxiliary battery terminal - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the No. 2 integration relay connector.

  1. Reinstall the No. 2 integration relay.

  1. Reconnect the positive (+) auxiliary battery terminal.

  1. Reconnect the negative (-) auxiliary battery terminal.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 2 INTEGRATION RELAY (EFI MAIN RELAY) - AUXILIARY BATTERY)
OK


6.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY (EFI MAIN RELAY) - BODY GROUND)
  1. Remove the No. 2 integration relay from the engine room relay block and junction block assembly.

  1. Disconnect the No. 2 integration relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1B-3 - Body ground
    Always
    Below 1 Ω

  1. Reconnect the No. 2 integration relay connector.

  1. Reinstall the No. 2 integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 2 INTEGRATION RELAY (EFI MAIN RELAY) - BODY GROUND)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

7.INSPECT NO. 2 INTEGRATION RELAY (IG2 RELAY)
  1. Inspect the No. 2 integration relay (IG2 relay) (Click here).



NG
REPLACE NO. 2 INTEGRATION RELAY (IG2 RELAY) (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY (IG2 RELAY) - ECM)
  1. Disconnect the ECM connector.

  1. Remove the No. 2 integration relay from the engine room relay block and junction block assembly.

  1. Disconnect the No. 2 integration relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    1A-4 - A57-28 (IGSW)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    1A-4 or A57-28 (IGSW) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the No. 2 integration relay connector.

  1. Reinstall the No. 2 integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 2 INTEGRATION RELAY (IG2 RELAY) - ECM)
OK


9.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY (IG2 RELAY) - AUXILIARY BATTERY)
  1. Remove the No. 2 integration relay from the engine room relay block and junction block assembly.

  1. Disconnect the No. 2 integration relay connector.

  1. Disconnect the negative (-) auxiliary battery terminal.

  1. Disconnect the positive (+) auxiliary battery terminal.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    1C-1 - Positive (+) auxiliary battery terminal
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    1C-1 or Positive (+) auxiliary battery terminal - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the No. 2 integration relay connector.

  1. Reinstall the No. 2 integration relay.

  1. Reconnect the positive (+) auxiliary battery terminal.

  1. Reconnect the negative (-) auxiliary battery terminal.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 2 INTEGRATION RELAY (IG2 RELAY) - AUXILIARY BATTERY)
OK


10.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY (IG2 RELAY) - BODY GROUND)
  1. Remove the No. 2 integration relay from the engine room relay block and junction block assembly.

  1. Disconnect the No. 2 integration relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1A-3 - Body ground
    Always
    Below 1 Ω

  1. Reconnect the No. 2 integration relay connector.

  1. Reinstall the No. 2 integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 2 INTEGRATION RELAY (IG2 RELAY) - BODY GROUND)
OK


11.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 2 INTEGRATION RELAY (IG2 RELAY))
  1. Remove the No. 2 integration relay from the engine room relay block and junction block assembly.

  1. Disconnect the No. 2 integration relay connector.

  1. Disconnect the power management control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    A22-2 (IG2D) - 1A-2
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    A22-2 (IG2D) or 1A-2 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the No. 2 integration relay connector.

  1. Reinstall the No. 2 integration relay.

  1. Reconnect the power management control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 2 INTEGRATION RELAY (IG2 RELAY))
OK

CHECK ENTRY AND START SYSTEM (Click here)