Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM (w/o EGR System)

DTC    P2237    Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)

DTC    P2238    Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)

DTC    P2239    Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)

DTC    P2252    Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)

DTC    P2253    Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)

for Preparation Click here


DESCRIPTION

Refer to DTC P2195 .

DTC No.
DTC Detection Condition
Trouble Area
P2237
Open in the circuit between terminals A1A+ and A1A- of the air fuel ratio sensor while engine is running (2 trip detection logic).
  1. Open in air fuel ratio sensor (sensor 1) circuit
  2. Air fuel ratio sensor (sensor 1)
  3. ECM
P2238
  1. Case 1
    Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic):
    (a) A1A+ voltage is 0.5 V or less
    (b) A1A+ - A1A- is 0.1 V or less
  2. Case 2
    Air fuel ratio sensor admittance is less than 0.0074 1/Ω (2 trip detection logic):
  1. Open or short in air fuel ratio sensor (sensor 1) circuit
  2. Air fuel ratio sensor (sensor 1)
  3. ECM
P2239
A1A+ voltage is higher than 4.5 V for 5 seconds (2 trip detection logic).
  1. Open or short in air fuel ratio sensor (sensor 1) circuit
  2. Air fuel ratio sensor (sensor 1)
  3. ECM
P2252
A1A- voltage is 0.5 V or less for 5 seconds (2 trip detection logic).
  1. Open or short in air fuel ratio sensor (sensor 1) circuit
  2. Air fuel ratio sensor (sensor 1)
  3. ECM
P2253
A1A- voltage is higher than 4.5 V for 5 seconds (2 trip detection logic).
  1. Open or short in air fuel ratio sensor (sensor 1) circuit
  2. Air fuel ratio sensor (sensor 1)
  3. ECM

WIRING DIAGRAM

Refer to DTC P2195 .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Refer to "Data List / Active Test" [AFS Voltage B1S1] (Click here).
  2. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. Sensor 1 refers to the sensor closest to the engine assembly.
  4. Sensor 2 refers to the sensor farthest away from the engine assembly.

1.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    D24-1 (HA1A) - D28-18 (HA1A)
    Always
    Below 1 Ω
    D24-3 (A1A+) - D28-103 (A1A+)
    Always
    Below 1 Ω
    D24-4 (A1A-) - D28-126 (A1A-)
    Always
    Below 1 Ω
    D24-1 (HA1A) or D28-18 (HA1A) - Body ground
    Always
    10 kΩ or higher
    D24-3 (A1A+) or D28-103 (A1A+) - Body ground
    Always
    10 kΩ or higher
    D24-4 (A1A-) or D28-126 (A1A-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the air fuel ratio sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2237, P2238, P2239, P2252 OR P2253)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the power switch off and wait for at least 30 seconds.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine and wait 5 minutes.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.

  1. Read the Pending DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P2237, P2238, P2239, P2252 or P2253 is output
    B



B
REPLACE ECM (Click here)
A

END