Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type)

NAVIGATION SYSTEM (for Radio and Display Type) > Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter

for Preparation Click here


DESCRIPTION

for Navigation Function:
  1. The radio and display receiver assembly receives a vehicle speed signal from the No. 3 meter circuit plate and sends the signal to extension module.
for Automatic Sound Levelizer (ASL) (for 6 Speakers):
  1. This circuit is necessary for the Automatic Sound Levelizer (ASL) built into the radio and display receiver assembly.
  2. The Automatic Sound Levelizer (ASL) function automatically adjusts the audio system volume level in order to compensate for increased vehicle noise (vehicle noise tends to increase as vehicle speed increases). The ASL adjusts the volume level based upon vehicle speed signals that it receives from the No. 3 meter circuit plate.
for "Bluetooth":
  1. Vehicle speed signals are received from the No. 3 meter circuit plate and used to cancel "Bluetooth" function operation.
    The radio and display receiver assembly recognizes that the vehicle is being to driven and makes it impossible to connect or register a "Bluetooth" device while driving.

HINT:
  1. A voltage of 12 V or 5 V is output from each ECU and then input to the No. 3 meter circuit plate. The signal is changed to a pulse signal at the transistor in the No. 3 meter circuit plate. Each ECU controls the respective system based on the pulse signal.
  2. If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.


WIRING DIAGRAM


E292833E01


INSPECTION PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)


    E227878
  1. Enter the "Vehicle Signal Check Mode" screen. Refer to Check Vehicle Signal Check Mode in Operation Check (Click here).

  1. While driving the vehicle, compare the "SPEED" indicator to the reading on the speedometer. Check if these readings are almost equal.

    HINT:
    The No. 3 meter circuit plate receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.

    OK:
    Vehicle speed displayed on the "Vehicle Signal Check Mode" screen is almost the same as the actual vehicle speed measured using the intelligent tester (Click here).



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT NO. 3 METER CIRCUIT PLATE (OUTPUT WAVEFORM)


    E210226E14
  1. Check the output waveform.

    1. Remove the No. 3 meter circuit plate with the connector still connected.

    2. Connect an oscilloscope to terminal L27-7 (+S) and body ground.

    3. Turn the power switch on (IG).

    4. Turn a wheel slowly.

    5. Check the signal waveform according to the condition(s) in the table below.
      Item
      Condition
      Measurement terminal
      L27-7 (+S) - Body ground
      Tool setting
      5 V/DIV., 20 ms./DIV.
      Vehicle condition
      Wheel being rotated

      OK:
      The waveform is similar to that shown in the illustration.

      HINT:
      When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.

      Text in Illustration 
      *a
      Component with harness connected
      (No. 3 Meter Circuit Plate)



NG
GO TO METER / GAUGE SYSTEM (Click here)
OK


3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (INPUT WAVEFORM)


    E241629E08
  1. Check the input waveform.

    1. Remove the radio and display receiver assembly with the connector still connected.

    2. Connect an oscilloscope to terminal L149-17 (SPD) and body ground.

    3. Turn the power switch on (IG).

    4. Turn a wheel slowly.

    5. Check the signal waveform according to the condition(s) in the table below.
      Item
      Condition
      Measurement terminal
      L149-17 (SPD) - Body ground
      Tool setting
      5 V/DIV., 20 ms./DIV.
      Vehicle condition
      Wheel being rotated

      OK:
      The waveform is similar to that shown in the illustration.

      HINT:
      When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.

      Text in Illustration 
      *a
      Component with harness connected
      (Radio and Display Receiver Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 3 METER CIRCUIT PLATE)
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)