Home › Engine / Hybrid System › 2ZR-FXE FUEL › FUEL TANK

FUEL TANK > INSTALLATION

for Preparation Click here



1. INSTALL FUEL TANK CUSHION


    A217133E01
  1. Install 3 new No. 1 fuel tank cushions and 2 new No. 2 fuel tank cushions as shown in the illustration.
    Text in Illustration 
    *1
    No. 1 Fuel Tank Cushion
    *2
    No. 2 Fuel Tank Cushion



2. INSTALL NO. 1 CHARCOAL CANISTER OUTLET HOSE


    A217132
  1. Install the hose clamp and the No. 1 charcoal canister outlet hose to the fuel tank.



3. INSTALL FUEL TANK ASSEMBLY
  1. Support the fuel tank using an engine lifter.



    A216431
  1. Raise the engine lifter, then install the fuel tank to the vehicle.

    NOTICE:
    1. Do not drop the fuel tank.
    2. When installing the fuel tank, tilt it slightly to prevent it from interfering with the suspension arm or other surrounding parts.



    A216432
  1. Tighten the 4 set bolts of the 2 fuel tank bands.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }

    NOTICE:
    First temporarily install the bolts of the tank bracket. Then temporarily install the bolts of the tank bands. Finally, tighten all of the bolts.



    A216430
  1. Connect the parking brake cable assembly with the 2 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



4. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


    A158830E06
  1. Align the fuel tube connector with the pipe, push the fuel tube connector in until the retainer makes a "click" sound, then lock the cover of the connector.

    NOTICE:
    1. Check that there are no scratches or foreign objects around the connected part of the fuel tube connector and pipe before starting this step.
    2. After connecting the fuel tank main tube sub-assembly, check that the fuel tank main tube sub-assembly is securely connected by pulling on the fuel tube connector.



5. CONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY


    A154751E03
  1. Push in the tube connector to the fuel pipe and install the retainer.

    NOTICE:
    1. Check if there is any damage or foreign objects on the connected part of the fuel pipe.
    2. After connecting, check if the fuel pipe and the connector are securely connected by pulling on them.



6. CONNECT FUEL TANK TO FILLER PIPE HOSE


    A217163E01
  1. Connect the fuel tank to filler pipe hose to the fuel tank as shown in the illustration, then fit it with the clamp.
    Text in Illustration 
    *1
    120°
    *2
    Upper Side



7. CONNECT FUEL TANK BREATHER TUBE


    A217130
  1. Connect the fuel tank breather tube to the fuel tank.

  1. Connect the No. 1 charcoal canister outlet hose.

    NOTICE:
    After connecting the breather tube and No. 1 charcoal canister outlet hose, check that the evaporation vent tube clamp is securely connected to the fuel tank.



8. INSTALL NO. 1 FUEL TANK PROTECTOR


    A216429
  1. Install the fuel tank protector sub-assembly with the 3 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



9. INSTALL REAR SUSPENSION BRACE SUB-ASSEMBLY


  1. Install the rear suspension brace sub-assembly with the 4 bolts and clip.


    C207257

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }



10. INSTALL REAR FLOOR SIDE MEMBER COVER LH


    C207250
  1. Install the rear floor side member cover LH with the nut and 2 bolts.



11. INSTALL REAR FLOOR SIDE MEMBER COVER RH


    C207251
  1. Engage the clip to temporarily install the rear floor side member cover RH.

  1. Install the rear floor side member cover RH with the 3 bolts.



12. ADD FUEL


13. INSTALL FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE
  1. Install the fuel suction tube assembly with pump and gauge (Click here).