Home › Engine / Hybrid System › 2ZR-FXE FUEL › FUEL TANK

FUEL TANK > INSTALLATION

for Preparation Click here



1. INSTALL FUEL TANK COVER VENT CASE SUB-ASSEMBLY


    A236113
  1. Install 2 new fuel tank cover vent case sub-assemblies as shown in the illustration.



2. INSTALL NO. 1 FUEL TANK CUSHION


    A236114E01
  1. Install 3 new No. 1 fuel tank cushions as shown in the illustration.
    Text in Illustration 
    *1
    No. 1 Fuel Tank Cushion



3. INSTALL NO. 1 CHARCOAL CANISTER OUTLET HOSE
  1. Install the hose clamp and the No. 1 charcoal canister outlet hose to the fuel tank.



4. INSTALL FUEL TANK ASSEMBLY
  1. Support the fuel tank using an engine lifter.

  1. Raise the engine lifter, then install the fuel tank to the vehicle.

    NOTICE:
    1. Do not drop the fuel tank.
    2. When installing the fuel tank, tilt it slightly to prevent it from interfering with the suspension arm or other surrounding parts.

  1. Tighten the 4 set bolts of the 2 fuel tank bands.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }

  1. Connect the parking brake cable assembly with the 2 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



5. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


    A158830E07
  1. Align the fuel tube connector with the pipe, push the fuel tube connector in until the retainer makes a "click" sound, then lock the cover of the connector.
    Text in Illustration 
    *1
    Lock Cover
    *2
    Retainer
    *3
    Nylon Tube
    *4
    Fuel Tube Connector
    *5
    Fuel Pipe
    *6
    O-ring
    *a
    Push

    NOTICE:
    1. Check that there are no scratches or foreign matter around the connected parts of the fuel tube connector and pipe before starting this step.
    2. After connecting the fuel tank main tube sub-assembly, check that the fuel tank main tube sub-assembly is securely connected by pulling on the fuel tube connector.



6. CONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY


    A154751E06
  1. Push in the tube connector to the fuel pipe and install the retainer.
    Text in Illustration 
    *1
    Rubber Hose
    *2
    O-ring
    *3
    Fuel Pipe
    *4
    Retainer
    *a
    Push

    NOTICE:
    1. Check if there is any damage or foreign matter on the connected parts of the fuel pipe.
    2. After connecting the fuel tube connector and pipe, check if they are securely connected by pulling on them.



7. CONNECT FUEL TANK TO FILLER PIPE HOSE


    A217163E02
  1. Connect the fuel tank to filler pipe hose to the fuel tank as shown in the illustration, then fit the hose with the clamp.
    Text in Illustration 
    *a
    120°
    *b
    Upper Side



8. CONNECT FUEL TANK BREATHER TUBE
  1. Connect the fuel tank breather tube to the fuel tank.

  1. Connect the No. 1 charcoal canister outlet hose.

    NOTICE:
    After connecting the breather tube and No. 1 charcoal canister outlet hose, check that the evaporation vent tube clamp is securely connected to the fuel tank.



9. INSTALL NO. 1 FUEL TANK PROTECTOR
  1. Install the fuel tank protector sub-assembly with the 3 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



10. INSTALL REAR SUSPENSION BRACE SUB-ASSEMBLY


  1. Install the rear suspension brace sub-assembly with the 4 bolts and clip.


    C207257

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }



11. INSTALL REAR FLOOR SIDE MEMBER COVER LH


    C207250
  1. Install the rear floor side member cover LH with the nut and 2 bolts.



12. INSTALL REAR FLOOR SIDE MEMBER COVER RH


    C207251
  1. Engage the clip to temporarily install the rear floor side member cover RH.

  1. Install the rear floor side member cover RH with the 3 bolts.



13. ADD FUEL


14. INSTALL FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE
(Click here)