EXHAUST MANIFOLD > REMOVAL |
| 1. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
| 2. REMOVE COWL BODY MOUNTING REINFORCEMENT LH (for LHD) |
![]() |
Remove the 3 bolts and cowl body mounting reinforcement LH.
| 3. REMOVE COWL BODY MOUNTING REINFORCEMENT LH (for RHD) |
![]() |
Remove the 3 bolts and cowl body mounting reinforcement LH.
| 4. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD) |
![]() |
Disengage the clamp and separate the wire harness.
![]() |
Disengage the claw and bend the No. 1 heater air duct splash shield seal.
![]() |
Disengage the claw and bend the water guard plate RH.
![]() |
Remove the 9 bolts and outer cowl top panel sub-assembly.
| 5. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD) |
![]() |
Disengage the clamp and separate the wire harness from the outer cowl top panel sub-assembly.
![]() |
Disengage the clamp*1 and disconnect the connector (w/ Windshield Deicer).
Disengage the clamp*2 and separate the wire harness from the outer cowl top panel sub-assembly.
![]() |
Disengage the claw and bend the No. 1 heater air duct splash shield seal.
![]() |
Disengage the claw and bend the water guard plate RH.
![]() |
Remove the 9 bolts and outer cowl top panel sub-assembly.
| 6. REMOVE NO. 1 ENGINE UNDER COVER |
| 7. REMOVE NO. 2 ENGINE UNDER COVER |
| 8. REMOVE FRONT NO. 3 ENGINE UNDER COVER |
![]() |
Remove the 4 clips and front No. 3 engine under cover.
| 9. REMOVE FRONT CENTER FLOOR BRACE |
![]() |
Remove the 4 bolts and front center floor brace.
| 10. DRAIN COOLANT (for Engine with Exhaust Heat Recirculation System) |
Loosen the radiator drain cock plug and drain the coolant.

| *1 | Reservoir Tank Cap | *2 | Radiator Drain Cock Plug |
| 11. REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Front and Rear Catalyst (w/ Exhaust Heat Recirculation System)) |
![]() |
Disconnect the 3 clamps and oxygen sensor connector.
![]() |
Disconnect the 2 heater water hoses.
![]() |
Remove the 4 bolts and 4 compression springs.
Remove the front exhaust pipe assembly from the 3 exhaust pipe supports.
Remove the 2 gaskets from the front exhaust pipe assembly (TWC: Front and Rear Catalyst) and exhaust manifold.
| 12. REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Front and Rear Catalyst (w/o Exhaust Heat Recirculation System)) |
![]() |
Remove the 4 bolts and 4 compression springs.
Remove the front exhaust pipe assembly from the 3 exhaust pipe supports.
Remove the 2 gaskets from the front exhaust pipe assembly (TWC: Front and Rear Catalyst) and exhaust manifold.
| 13. REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR |
![]() |
Remove the 3 nuts and front No. 1 floor heat insulator.
| 14. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR |
![]() |
Remove the 3 bolts and No. 1 exhaust manifold heat insulator.
| *A | w/ EGR System |
| *B | w/o EGR System |
| 15. REMOVE AIR FUEL RATIO SENSOR |
![]() |
Disconnect the air fuel ratio sensor connector and clamp.
![]() |
Using SST, remove the air fuel ratio sensor.
| 16. REMOVE MANIFOLD STAY |
![]() |
Remove the 3 bolts and manifold stay.
| 17. REMOVE EXHAUST MANIFOLD |
w/ EGR System:
![]() |
Remove the 7 nuts, exhaust manifold and 2 gaskets.
w/o EGR System:
![]() |
Remove the 5 nuts, exhaust manifold and gasket.
| 18. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR |
![]() |
Remove the 3 bolts and No. 2 exhaust manifold heat insulator.
| *A | w/ EGR System |
| *B | w/o EGR System |