DTC B1500 Fuel Sender Open Detected |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1500 | When IG voltage is 9.5 V or more and the following conditions is detected:
|
|

| 1.READ VALUE USING INTELLIGENT TESTER (FUEL INPUT) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Combination Meter / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Fuel Input | Fuel input signal/Min.: 0, Max.: 127.5 | 10th segment comes on: 39.6 to 45.0 | Unit: Liter |
| 9th segment comes on: 35.7 to 39.6 | |||
| 8th segment comes on: 31.8 to 35.7 | |||
| 7th segment comes on: 27.9 to 31.8 | |||
| 6th segment comes on: 24.0 to 27.9 | |||
| 5th segment comes on: 20.1 to 24.0 | |||
| 4th segment comes on: 16.2 to 20.1 | |||
| 3rd segment comes on: 12.3 to 16.2 | |||
| 2nd segment comes on: 8.4 to 12.3 | |||
| 1st segment comes on: 6.1 to 8.4 |
| Result | Proceed to |
| Fuel level data can be displayed on the intelligent tester and DTC B1500 is output. | A |
| Fuel level data cannot be displayed on the intelligent tester. | B |
|
| ||||
| A | ||
| ||
| 2.INSPECT FUEL SENDER GAUGE ASSEMBLY |
![]() |
Disconnect the L27 connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L27-14 (L) - L27-15 (ES2) | Always | 12.0 to 415 Ω |
| *1 | Front view of wire harness connector (to Combination Meter Assembly) |
|
| ||||
| OK | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (NO. 3 METER CIRCUIT PLATE - FUEL SENDER GAUGE ASSEMBLY) |
Disconnect the R11 connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L27-14 (L) - R11-2 (FS) | Always | Below 1 Ω |
| L27-14 (L) - Body ground | Always | 10 kΩ or higher |
| L27-15 (ES2) - R11-3 (FE) | Always | Below 1 Ω |
| L27-15 (ES2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT FUEL SENDER GAUGE ASSEMBLY |
![]() |
Remove the fuel sender gauge assembly (Click here).
Check that the float moves smoothly between E and F.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Float level is F (upper) | 12 to 18 Ω |
| 1 - 2 | Float level is between F (upper) and E (lower) | 12 to 415 Ω (Gradually changes) |
| 1 - 2 | Float level is E (lower) | 405 to 415 Ω |
| *1 | Front view of wire harness connector (to Fuel Sender Gauge Assembly) |
|
| ||||
| OK | |
| 5.REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE) |
Replace the combination meter assembly (meter circuit plate) to a new or a known good one (Click here).
|
| ||||
| OK | ||
| ||