Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

DTC    B1500    Fuel Sender Open Detected

for Preparation Click here


DESCRIPTION

This DTC is stored when the combination meter assembly (No. 3 meter circuit plate) detects a fuel sender gauge malfunction via a direct line.

DTC No.
DTC Detection Condition
Trouble Area
B1500
When IG voltage is 9.5 V or more and the following conditions is detected:
  1. Fuel sender gauge operation malfunction
  1. Harness or connector
  2. Fuel sender gauge assembly
  3. Combination meter assembly (No. 3 meter circuit plate)

WIRING DIAGRAM


E156126E23


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (FUEL INPUT)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Combination Meter / Data List.

  1. Check the values by referring to the table below.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Fuel Input
    Fuel input signal/Min.: 0, Max.: 127.5
    10th segment comes on: 39.6 to 45.0
    Unit: Liter
    9th segment comes on: 35.7 to 39.6
    8th segment comes on: 31.8 to 35.7
    7th segment comes on: 27.9 to 31.8
    6th segment comes on: 24.0 to 27.9
    5th segment comes on: 20.1 to 24.0
    4th segment comes on: 16.2 to 20.1
    3rd segment comes on: 12.3 to 16.2
    2nd segment comes on: 8.4 to 12.3
    1st segment comes on: 6.1 to 8.4

    Result:

    Result
    Proceed to
    Fuel level data can be displayed on the intelligent tester and DTC B1500 is output.
    A
    Fuel level data cannot be displayed on the intelligent tester.
    B



B
Go to step 2
A

REPLACE COMBINATION METER ASSEMBLY (NO. 3 METER CIRCUIT PLATE) (Click here)  

2.INSPECT FUEL SENDER GAUGE ASSEMBLY


    E160303E47
  1. Disconnect the L27 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Type A:
    Tester Connection
    Condition
    Specified Condition
    L27-14 (L) - L27-15 (ES2)
    Always
    13.5 to 414.5 Ω
    Type B:
    Tester Connection
    Condition
    Specified Condition
    L27-14 (L) - L27-15 (ES2)
    Always
    12.0 to 415.0 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Combination Meter Assembly)



NG
Go to step 3
OK

REPLACE COMBINATION METER ASSEMBLY (NO. 3 METER CIRCUIT PLATE) (Click here)  

3.CHECK HARNESS AND CONNECTOR (NO. 3 METER CIRCUIT PLATE - FUEL SENDER GAUGE ASSEMBLY)
  1. Disconnect the R11 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L27-14 (L) - R11-2 (FS)
    Always
    Below 1 Ω
    L27-14 (L) - Body ground
    Always
    10 kΩ or higher
    L27-15 (ES2) - R11-3 (FE)
    Always
    Below 1 Ω
    L27-15 (ES2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT FUEL SENDER GAUGE ASSEMBLY
  1. Remove the fuel sender gauge assembly (Click here).


A325307E02

  1. Check that the float moves smoothly between E and F.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Type A:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Float level is F (upper)
    13.5 to 16.5 Ω
    1 - 2
    Float level is between F (upper) and E (lower)
    13.5 to 414.5 Ω (Gradually changes)
    1 - 2
    Float level is E (lower)
    405.5 to 414.5 Ω
    Type B:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Float level is F (upper)
    12.0 to 18.0 Ω
    1 - 2
    Float level is between F (upper) and E (lower)
    12.0 to 415.0 Ω (Gradually changes)
    1 - 2
    Float level is E (lower)
    405.0 to 415.0 Ω

    Text in Illustration 
    *A
    Type A
    *B
    Type B
    *1
    Component without wire harness connected
    (Fuel Sender Gauge Assembly)
    -
    -



NG
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
OK


5.REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)
  1. Replace the combination meter assembly (meter circuit plate) to a new or a known good one (Click here).

    OK:
    The operation of the fuel receiver gauge returns to normal.



NG
REPLACE COMBINATION METER ASSEMBLY (NO. 3 METER CIRCUIT PLATE)
OK

END