Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM

DTC    B279A    Theft Deterrent System Communication Line High Fixation

for Preparation Click here


DESCRIPTION

If the communication line (EFIO - IMI) to the certification ECU assembly (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 is stuck high output (e. g. shorted to +B), the power management control ECU (HV CPU) stores this DTC.
  1. *1: w/o Airbag Cut-off Switch
  2. *2: w/ Airbag Cut-off Switch

DTC No.
DTC Detection Condition
Trouble Area
B279A
When the communication line (EFIO - IMI) between power management control ECU (HV CPU) and certification ECU assembly (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 is stuck high output.
  1. Wire harness or connector
  2. Power management control ECU (HV CPU)
  3. Certification ECU (Smart key ECU assembly)*1
  4. ID code box (Immobiliser code ECU)*2
  5. Telephone transceiver assembly*3
  1. *1: w/o Airbag Cut-off Switch
  2. *2: w/ Airbag Cut-off Switch
  3. *3: w/ Blocking System

WIRING DIAGRAM


w/o Airbag Cut-off Switch

B203372E17


w/ Airbag Cut-off Switch

B331617E03


INSPECTION PROCEDURE

NOTICE:
  1. If the certification ECU (smart key ECU assembly) is replaced, register all the keys and ECU communication ID.*1
  2. If the ID code box (immobiliser code ECU) is replaced, register the ECU code and ECU communication ID.*2
  3. When telephone transceiver is replaced, it is necessary to set the contract mode.*3
    1. *1: w/o Airbag Cut-off Switch
    2. *2: w/ Airbag Cut-off Switch
    3. *3: w/ Blocking System

1.CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs (Click here).

    HINT:
    If any DTCs other than DTC B279A are output, troubleshoot those DTCs first.

    Result:
    Result
    Proceed to
    DTC B279A is output
    A
    DTC B279A and other DTCs are output
    B



B
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
A


2.SYSTEM CHECK
  1. Check the vehicle specification.

    Result:
    Result
    Proceed to
    w/ Blocking System
    A
    w/o Blocking System
    B



B
Go to step 9
A


3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - TELEPHONE TRANSCEIVER ASSEMBLY)
  1. Disconnect the telephone transceiver assembly connector.

  1. Disconnect the power management control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L156-8 (BLK3) - L6-21 (IMI)
    Always
    Below 1 Ω
    L6-21 (IMI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - TELEPHONE TRANSCEIVER ASSEMBLY)
  1. Disconnect the ID code box (immobiliser code ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L156-2 (BLK4) - L10-6 (EFIO)
    Always
    Below 1 Ω
    L10-6 (EFIO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
  1. Temporarily replace the telephone transceiver assembly with a new or known good one.

    HINT:
    Refer to the Service Bulletin.


NEXT


6.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.

    HINT:
    Refer to the Service Bulletin.


NEXT


7.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


8.CHECK DTC OUTPUT
  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B279A is not output.



NG
Go to step 18
OK

END (TELEPHONE TRANSCEIVER ASSEMBLY WAS DEFECTIVE) 

9.SYSTEM CHECK
  1. Check the vehicle specification.

    Result:
    Result
    Proceed to
    w/o Airbag Cut-off Switch
    A
    w/ Airbag Cut-off Switch
    B



B
Go to step 16
A


10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - POWER MANAGEMENT CONTROL ECU (HV CPU))
  1. Disconnect the certification ECU (smart key ECU assembly) connector.



    B229596E02
  1. Disconnect the power management control ECU (HV CPU) connector.

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L62-35 (EFIO) - L6-21 (IMI)
    Always
    Below 1 Ω
    L6-21 (IMI) - Body ground
    Always
    10 kΩ or higher

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L6-21 (IMI) - Body ground
    Always
    Below 1 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Certification ECU (Smart Key ECU Assembly))
    *2
    Front view of wire harness connector
    (to Power Management Control ECU (HV CPU))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (WAVEFORM)
  1. Reconnect the certification ECU (smart key ECU assembly) connector.



  1. Reconnect the power management control ECU (HV CPU) connector.


    B229599E02

  1. Using an oscilloscope, check the waveform.

    Waveform (Reference):
    Item
    Content
    Terminal No. (Symbol)
    L62-35 (EFIO) - L62-15 (E)
    Tool Setting
    5 V/DIV., 50 msec./DIV.
    Condition
    Power switch on (IG)

    OK:
    Waveform is output normally (see illustration).


    Text in Illustration 
    *1
    Component with harness connected
    (Certification ECU (Smart Key ECU Assembly))
    *2
    GND
    *3
    HIGH
    *4
    LOW



NG
Go to step 12
OK

REPLACE POWER MANAGEMENT CONTROL ECU (HV CPU) (Click here)  

12.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Replace the certification ECU (smart key ECU assembly).

    HINT:
    Refer to the Service Bulletin.


NEXT


13.KEY REGISTRATION
  1. Register the key.

    HINT:
    Refer to the Service Bulletin.


NEXT


14.ECU COMMUNICATION ID REGISTRATION
  1. Register the ECU communication ID.

    HINT:
    Refer to the Service Bulletin.


NEXT


15.CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs (Click here).

    OK:
    DTC B279A is not output.



NG
REPLACE POWER MANAGEMENT CONTROL ECU (HV CPU) (Click here)
OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE) 

16.CHECK HARNESS AND CONNECTOR (ID CODE BOX - POWER MANAGEMENT CONTROL ECU (HV CPU))
  1. Disconnect the ID code box (immobiliser code ECU) connector.



    B219313E04
  1. Disconnect the power management control ECU (HV CPU) connector.

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L10-6 (EFIO) - L6-21 (IMI)
    Always
    Below 1 Ω
    L6-21 (IMI) - Body ground
    Always
    10 kΩ or higher

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L6-21 (IMI) - Body ground
    Always
    Below 1 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to ID Code Box (Immobiliser Code ECU))
    *2
    Front view of wire harness connector
    (to Power Management Control ECU (HV CPU))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


17.CHECK ID CODE BOX (IMMOBILISER CODE ECU) (WAVEFORM)
  1. Reconnect the ID code box (immobiliser code ECU) connector.



    B232678E01
  1. Reconnect the power management control ECU (HV CPU) connector.

  1. Using an oscilloscope, check the waveform.

    Waveform (Reference):
    Item
    Content
    Terminal No. (Symbol)
    L10-6 (EFIO) - L10-8 (GND)
    Tool Setting
    5 V/DIV., 50 msec./DIV.
    Condition
    Power switch on (IG)

    OK:
    Waveform is output normally (see illustration).

    Text in Illustration 
    *1
    Component with harness connected
    (ID Code Box (Immobiliser Code ECU))
    *2
    GND
    *3
    HIGH
    *4
    LOW



NG
Go to step 18
OK

REPLACE POWER MANAGEMENT CONTROL ECU (HV CPU) (Click here)  

18.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
  1. Replace the ID code box (immobiliser code ECU).

    HINT:
    Refer to the Service Bulletin.


NEXT


19.ECU CODE REGISTRATION
  1. Register the ECU code.

    HINT:
    Refer to the Service Bulletin.


NEXT


20.ECU COMMUNICATION ID REGISTRATION
  1. Register the ECU communication ID.

    HINT:
    Refer to the Service Bulletin.


NEXT


21.CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs (Click here).

    OK:
    DTC B279A is not output.



NG
REPLACE POWER MANAGEMENT CONTROL ECU (HV CPU) (Click here)
OK

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)